A steady flow system receives 4.56Kg per minute of a fluid where P1 = 137.90 Kpa, v1 = 0.0388 m3/Kg, V1 = 122 m/s, u1 = 17.16 KJ/Kg. The fluid leaves the system at a boundary where P2 = 551.6 Kpa, v2 = 0.193 m3/Kg, , V2 = 183 m/s, u2 = 52.80 KJ/Kg. During the passage through the system, the fluid receives 3,000 J/s of Heat. Determine the work in watts

A steady flow system receives 4.56Kg per minute of a fluid where P1 = 137.90 Kpa, v1 = 0.0388 m3/Kg, V1 = 122 m/s, u1 = 17.16 KJ/Kg. The fluid leaves the system at a boundary where P2 = 551.6 Kpa, v2 = 0.193 m3/Kg, , V2 = 183 m/s, u2 = 52.80 KJ/Kg. During the passage through the system, the fluid receives 3,000 J/s of Heat. Determine the work in watts

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Fluid Mechanics
I need answers in less than an hour T.T. Thank you!
A Liquid fluid with a density of 1,750 kg/m3 from an elevated 2m open reservoir (P1=0 bars) flows before the pump at 7.5 m/s. The liquid fluid is pumped at an unknown final velocity to a 75 meter elevated tank with a pressure reading of 7.75 Bars. assuming Friction losses is 757.75J and the actual WORK of the pump is 1,933,400J. Calculate the power in HP if the pump's efficiency is just 75% and for every 1,000 kg of fluid per hour.
solve the following question and show the complete solutions
Steam enters a turbine with a pressure of P1= 4888 kPa, specific internal energy u1= 3612 kJ/kg, mass flow rate of 7.5kg/s and density of 1.112 kg/m3. Steam leaves at P2 = 224 kPa with a density of 4.5kg/m3 and a specific internal energy of u2= 1224 kJ/kg. Heat loss from the device by radiation is 50KJ/kg. Neglecting the changes in kinetic and potential energies, determine the power produced by the system.
4.3 Water jets pump (Fig. P4.3) involves a jet cross-sectional area of 0.01 m2, and a jet area associated with the jet and entrained stream is 0.075 m2. These two fluid velocity of 30 m/s. The jet is surrounded by entrained water. The total croSs sectional streams leave the pump thoroughly mixed with an average velocity of 6 m/s through a cross-sectional area of 0.075 m2. Determine the pumping rate (i.e. the entrained fluid flow rate) involved in liters/s. having shown in a dian o 6 mis Entrained water 30 mis jet Entrained water 4.9 A 4.4 An appropriate turbulent pipe flow velocitu Fig. P4.3
Fluid falls from a 50 m elevation.a. Determine the velocity of the fluid at the surface of the reservoir.b. What is the temperature of the water in the reservoir?Let heat capacity of the fluid equal to 4.19 kj/kg* °C. Assume a steady-state and adiabatic process.
Q.3 In a steady flow of water, water is coming in through Pipe 1 (area 1 m, velocity 1 m/ s) and Pipe 2 (area 2 m, velocity 2 m/s) and 2. going out through Pipe 3 (area 2.5 m-). The exit velocity of Pipe 3 is? A 3 m/s В 6 m/s 5 m/s D 2 m/s