A starter turns very slowly and has excessive cranking current draw. When removed from the vehicle and bench tested, the starter spins normally and current draw is within specifications. Technician A says poor battery connections may be the cause. Technician B says an internal engine problem may be the cause. Who is correct

A starter turns very slowly and has excessive cranking current draw. When removed from the vehicle and bench tested, the starter spins normally and current draw is within specifications. Technician A says poor battery connections may be the cause. Technician B says an internal engine problem may be the cause. Who is correct

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter14: Troubleshooting Electric Control Devices

Section: Chapter Questions

Problem 2RQ

See similar textbooks

Similar questions

c) Based on Figure 3 (c), a basic DOL starter induction motor at a power station is experiencing run-time error and unable to start, based on your understanding, interpret the sequence of troubleshooting shall be carried out to identify the root cause of the abnormalities. 3P 1P MCB MCB STOP K1 START MOTOR Figure 3 (c)
3.) The time delay fuse using the strict standard rating for 2Ø, 230 V, 7.5 hp SCIM motor is A. 25 A B. 30 A C. 35 A D. Any of the above
Explain the characteristics and how the following motor starters work. 1.Slip Ring a. Variable Resistance b. Fixed Starting Resistance
Technician A says when testing the voltage output, if the charging voltage is too high, the cause could be an open field wire from the regulator. Technician B says a loose or glazed drive belt could be the cause of too high charging voltage. Who is correct? A only B only Both A and B Neither A or B Technician A says that poor connection at the generator output wire can cause charging systems problems. Technician B says that many charging system circuits contain a circuit protection device. Who is correct? A only B only Both A and B Neither A or B
3 Phase Induction motor I want a short answer please 11. The number of three-phase induction motor parts and the function of each part. 12. How to know the terminals of an induction motor if they are not encoded in the terminal box. 13. How can a three-phase induction motor be reversed? 14. Number of tools used to protect devices - transformers and induction motors - in the laboratory. 15. The number of devices required to conduct a test No load. for a three-phase induction motor 16. The number of devices required to conduct a test For a three-phase induction motor, a Blocked rotor 17. What is the use of a test? For a three-phase induction motor? Blocked rotor and No load 18. When conducting the no-load test, the current rises in the first second of preparation when using the direct connection method. the reasons for that? 19. When performing a non-pregnancy test, we notice a decrease in the ability factor. the reasons for that? 20. Connect an induction motor directly to the source.…
If a centrifugal switch assembly in a split-phase or capacitor motor fails, you'll most likely have a A. slowly turning motor.B. loudly humming motor.C. motor turning at too high a speed. D. motor that has reversed direction while running.
QUESTION 12 The proper way to determine the required over-current protection is to: determine the FLA based on the nameplate. Use the standard rule of thumb that the over-current protection shall be 7 to 10x the locked rotor amps. determine the watts by converting the HP rating on the nameplate to watts. to determine the FLC by looking up the value in the appropriate table(s) in the NEC as they relate to the horsepower of the motor.
Explain how does the current will be reduced during the starting of the motor.
Industrial Motor Controls 8.a. A typical motor speed control circuit that is controlled by an analog current loop will have a current ofA. 4-20 mA.B. 2-20 mA.C. 5-50 mA.D. 0-10 mA.8.b. Which one of the following statements is true of a disabled contact or coil?A. The disabled element has been automatically disabled due to module failure.B. The disabled element is held false by the PLC.C. A disabled contact or coil is caused by a faulty memory location in the PLC.D. A contact must be in the disabled state before it can be forced ON or OFF.
What is the necessity of 3point starter? What is starter ?
1. It is a machine that converts mechanical energy to electrical energy. 2. It is a machine that converts electrical energy to mechanical energy. 3. It is cylindrical or drum-shaped where the coils are placed and can either be lap wounded or wave wounded. 4. It connects the commutator to the other parts of the DC machine. 5. It serves as the housing of the dc machine. 6. True or False: The shunt field winding is part of the armature. 7. True or False: The long shunt compound generator is when the armature is in series with the series field winding and parallel to the shunt field winding. 8-10. Your newly built house needs an elevator. Which from the following will be best to use- series, shunt or compound motor and why?
Explain the operation of the direct current motor used in mini-split units.