answer in 30 mins. thank you A square steel bar is 50 mm on a side and 250 mm long. It is loaded by an axial tensileforce of 200 kN. If E = 200 GPa and µ = 0.3, determine the change of volume per unitvolume.O a. 130 GPaO b.140 GPaO c.110 GPaO d. 120 GPa

GIVEN DATA- SIDE OF SQUARE a=50mm L=250mm E=200GPa P=200KN POISSON RATIO=0.3 WE HAVE TO FIND…

Answered: A square steel bar is 50 mm on a side…

A square steel bar is 50 mm on a side and 250 mm long. It is loaded by an axial tensile force of 200 kN. If E = 200 GPa and μ = 0.3, determine the change of volume per unit volume.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Mechanical
The figureshows a copper rod that is placed in an aluminum tube. The rod is 0.005 in. longer than the tube of length L = 10.14 in. Find the maximum safe load P (in lb with four decimal places) that can be applied to the bearing plate, using the following data: area of copper = 2.78 sq, in. area of aluminum = 3.28 sq, in. E of copper = 17013025 ksi E of aluminum = 10072240 ksi allowable stress for copper = 19000 ksi allowable stress for aluminum = 10802 ksi
solve pls ps. change 4.5m to 4.5ft
Problem 2 You will be determining the value for the external load P that will cause the diameter of BC to change to 5.8 mm. The original diameter of BC is 6 mm. Use the values given below unless otherwise stated by the questions. E = 200 GPa V = 0.38 300 mm 400 mm B 1 -200 mm-
E. Rigid bar AD is horizontal before the weight of 112 lb is applied to the end of wire BC at C. The wires have a radius of 0.025" and are made of A913 steel. Determine the rotation of AD and how far C will move down due to application of the weight See Appendix of text for any material properties needed. Ans: 0.00071 radians 3 ft - 2 ft -3 ft- D B 4 ft W
1. A steel column has an ultimate compressive stress of 135 MPa. If it supports a load of 200 kN, find the diameter of the column using a factor of safety of 3. A. 65.34 mm B. 75.22 mm C. 45.23 mm D. 56.34 mm
If load P = 17.3 kips, determine the normal force in bar (1). A 6 ft 36.5 kips 28.8 kips 17.7 kips O 34.3 kips O 31.4 kips D B (1) 4 ft
If load P = 22.9 kips, determine the normal force in bar (1). D P A 6 ft 51.9 kips 44.8 kips 27.3 kips 38.2 kips O 40.4 kips B (1) 4 ft
A copper wire of length 1.80 m and diameter 0.80 mm is suspended from two points, 1.0 m apart and at the same horizontal level. A load of 2.5 kg is hung from the centre of the wire. The wire makes an angle 8 to the vertical at point P and experiences a force F as shown in the diagram below. THIS DIAGRAM IS NOT SHOWN TO SCALE i. 0.9 m ii. 0.5 m F Ꮎ : Ꮎ 0.5 m F 0.9 m Calculate the angle with which each part of the wire makes with the vertical at the point where the load is hung. Determine the stress in the wire. iii. Determine the strain in the wire. m = 2.5 kg (Young's modulus for copper = 1.17 x 10¹¹ Pa) iv. Determine the extension produced in the wire by this strain.
2-1. A standard steel specimen of in. dia- meter elongated 0.0087 in. in an 8 in. gage length when it was subjected to a tensile force of 6,250 lb. If the specimen was known to be in the elastic range, what is the elastic modulus of the steel? Ans: 29.3 x 106 psi.
pls help me answer this asap. thank you!!
The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.31 in2. Find the vertical displacement (in inches and absolute value) of point Coaused by the 2888-lb load if x = 8.7 ft and 8 = 46.5-. Use E = 29159 ksi for steel. Note: Round off the final answer to four decimal places. Rigid B P