A square reinforced-concrete pier 0.3 x 0.3 m in cross section and 1.2m high is loaded as shown in the figure. The concrete is strengthened by the addition of cight vertical 25 x 25 mm square steel reinforcing bars placed symmetrically about the vertical axis of the pier. Find the stress (force/unit area) in the steel and concrete and the dellection. For Concrete, take E= 17 GN/m?

A square reinforced-concrete pier 0.3 x 0.3 m in cross section and 1.2m high is loaded as shown in the figure. The concrete is strengthened by the addition of cight vertical 25 x 25 mm square steel reinforcing bars placed symmetrically about the vertical axis of the pier. Find the stress (force/unit area) in the steel and concrete and the dellection. For Concrete, take E= 17 GN/m?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 75 mm x 75 mm wooden block in cross section is subjected to a load P of 300 kN. The plane A makes an angle of 14 degrees with respect to the horizontal axis (x-axis). a. Determine the normal stress at section A-A. b. Determine the shear stress at section A-A.
I need to solve this in concrete
The concrete column (300 mm x 300 mm) is reinforced by four steel bars each having diameter of 30 mm as shown in Figure Q1. The working stresses for steel and concrete are 200 MPa and 25 MPa, respectively. Determine the largest axial force P that can be safely applied to the column. Use Est - 200 GPa and Eco = 20 GPa. Dimensions in mm 300 300
Question A prestressed concrete rectangular beam has area of cross-seciton equal to 36000mm² and moment of inertia of 2.7 x 108 mm4. A prestressing force of 195 kN is applied by tendons at an eccentricity of 55 mm from neutral axis. The loss of stress in steel due to creep of concrete is N/mm². [Take E = 2 × 105 N/mm², Ec = 3 x 105 N/mm² and creep coefficient = 1.50]
2. A 300 mm x 400 mm concrete beam has a span of 5.5m. A post tension force of 600 kN was applied at a point 60mm above the bottom of the beam. Assume concrete would not crack in tension. f.=20.7MPA. Unit weight of concrete is 23.5 kN/m3. Compute the following: а. Deflection due to prestressing force of 600 kN. b. Net deflection of the beam immediately after transfer. 60mm 5.5m
Determine the maximum and concrete and steel stresses at the point of maximum positive and negative moments
A wood beam is strengthened using two steel plates as shown in the figure below. V 6 mm 150 mm 6 mm |B 100 mm i The beam has simple supports and an overhang and is subjected to a point load and a uniform load as shown in the figure below. 13 KN q= 5.0 kN/m с 3 m Calculate the maximum tensile and compressive stresses of the beam. Assume that E = 11 GPa and E = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention.) maximum tensile stress in wood MPa maximum tensile stress in steel MPa MPa maximum compressive stress in wood maximum compressive stress in steel MPa Need Help? Read It B 000 +1m-
The masonry pier is subjected to the F = 780 kN load. Consider x = 0.25 mm and y = 0.5 mm. Neglect the weight of the pier. Part A Determine the normal stress at corner A. Express your answer with the appropriate units. Part B Determine the normal stress at corner B. Express your answer with the appropriate units. Part C Determine the normal stress at corner C. Express your answer with the appropriate units.
You must have to draw FBD
The column is constructed from high-strength concrete and eight A992 steel reinforcing rods. The column is subjected to an axial force of P=210 kip. Each rod has a diameter of 1 in.in. For A992 steel, Est=29.0(103)ksi, and for high-strength concrete, Ec=4.20(103)ksi. Determine the average normal stress in the concrete and in each rod. (Please type answer no write by hend)