A square block 30cm square and 25cm deep is floated on a body of liquid which consists of 20cm layer of water above the layer of Hg. The block weighs 18840. If a downward vertical force 1100N is applied to the center of this block, determine the location of the top edge of metal block before and after the vertical force is applied.

A square block 30cm square and 25cm deep is floated on a body of liquid which consists of 20cm layer of water above the layer of Hg. The block weighs 18840. If a downward vertical force 1100N is applied to the center of this block, determine the location of the top edge of metal block before and after the vertical force is applied.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please be clear
Determine principal stress
Shear Stress H.W W= lo EN/m 5m T= ?
Plate with 0.13m wide and 0.25 m length passes thru oil ewith layer 3.5mm and 5mm thick. Both surface sides of the plate touch the oil that has a viscosity of u=0.038 Ns/m^2. Determine the force required (in Newton) to move the plate at speed of 5 mm/s
A 150 mm diameter rivet resists a shear force of V =8 kN. Find the average shear stress in the rivet. %3D 150 mm (A) 230 kPa (B) 370 kPa (C) 430 kPa (D) 450 kPa
5. Calculate the depth of neutral axis at balanced condition if the effective depth is 250 mm and fy is 415 MPa. a. 147.78 mm b. 212.50 mm c. 294.12 mm d. 223.25 mm 6. Calculate the stress at the centroid of the tension steel in single layer if the effective depth is 250 mm and the depth of neural axis is 100 mm. a. 800 MPa b. 500 MPa c. 1000 MPa d. 900 MPa 7. Calculate the strain at the centroid of the tension steel in single layer if the effective depth is 250 mm and the depth of neural axis is 100 mm. a. 0.0040 b. 0.0025 c. 0.0050 d. 0.0045 8. Calculate the depth of compression at balanced condition if the effective depth is 250 mm, β1=0.85, and fy is 415 MPa. a. 180.63 MPa b. 135.57 MPa c. 125.61 MPa d. 178.86 MPa
show complete FBD
A 40m steel tape is suspended in the air between a theodolite and vertical rod, which is placed exactly at the 40m mark, under a pull of 12.5kg. The slope of the measured line is 2-degree 40minutes. The tape weighs 1kg, standard pull of 8.5kg, cross-sectional area of 0.039cm^2 and E= 2x10^6 kg/cm^2. a. Determine the correction for sag of the tape in meter.b. Determine the horizontal distance between the theodolite and rod in meters. (Apply 5-decimal places - for letter B only)c. What additional pull must be applied to eliminate the effect of sag?
Determine maximum principal stress
32 H.W find longitudinal and hov tensile stresses in the wall of vessel Shown in figue, if the internal Pessure is 09 MA and thickness of Wall is 6.44mm? Ans: o =42.19 M H= 62.8 Ma %3D t. AIS finel I?so67 0.6m
Find stress
Determine the principal stress in the beam at point A. 60 kN 50 mm 150 KN 150 mm mm -05m- -025m