A spur gear set is shown in Figure Q6(a). The pinion 2 rotates at 750 revolutions/minute and transmits 1.8 kW to the driven gear 3. The teeth pressure angle is 20 degrees with a module m = 2.5 mm. 30 Teeth - 20 Teeth Figure Q6(a) Determine the forces that act on gear 3 from the pinion. i). ii). Draw a free-body diagram of gear 3.

A spur gear set is shown in Figure Q6(a). The pinion 2 rotates at 750 revolutions/minute and transmits 1.8 kW to the driven gear 3. The teeth pressure angle is 20 degrees with a module m = 2.5 mm. 30 Teeth - 20 Teeth Figure Q6(a) Determine the forces that act on gear 3 from the pinion. i). ii). Draw a free-body diagram of gear 3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 1: Gears The lath machine in the Central University of Technology (CUT) mechanicalworkshop uses epicyclic gear train shown in Figure 1 to operate. Plate gear C of this gear system are carried on the arm A and free to rotated. the pitch circle diameter of the internally toothed ring gear D is to be 214 mm and the module 4 mm. When the ring gear D is stationary, the arm A, which carries three planet wheels C of equal size, is to make one revolution in the same direction as the sun wheel B for every five revolutions of the driving spindle carrying the sunwheel B Figure 1 attached 1.1. Calculate the number of teeth of the ring gear D. 1.2. State an equation tha relate the number of teeth of gear D, B and C. 1.3. Use the table method to calculate the number of teeth of gear B. 1.4. Calculate the number of teeth for gear C.
Q2. Figure Q2 shows a simple gear train. At the instant shown, a force F = 1100 N is applied at one end of a 0.175 m long lever, perpendicular to the length of the lever. The other end of the lever is attached to shaft 1, and so the lever turns shaft 1. Gear A is attached to shaft 1 and has 48 teeth, Gear A is meshed with gear B, which has 16 teeth. a) What is the gear ratio from gear A to gear B? The efficiency of power transmission between the two gears is 70%. The moment of inertia of shaft 1, including the lever and gear A is 1.05 kgm² and the moment of inertia of gear B is 0.15 kgm². The frictional torque on shaft 1 is 0.2 Nm and the frictional torque on gear B is 0.7 Nm. If, at the instant show, the lever is moving downwards with a velocity of 1.4 m/s and an acceleration of 0.15 m/s², determine: b) the torque transmitted to gear A. c) the torque transmitted to gear B. d) the power transmitted to gear B. 1100 N 1.4 m/s 0.15 m/s² ME22002 Lever 0.175 m Gear A Gear B Figure Q2 END OF…
Q4: The reverted gear train shown in Fig.(1) has the following data, Circular pitch Pc=0.4 teeth/mm , T1=15, T2=30, T3=20 , N1= 150 rpm (cw) • Determine: • 1. module of gear train (m=?) Output Input 2.Pitch diameter of gears (D1, D2, D3, D4) • 3. The centre distance between shafts (C) • 4. Gear ratio (G), and Train value (TV) • 5. output speed (N4) 4/14/2020
Q4: In an epicyclic gear train shown in the figure, the number of teeth of gear (A and S) are (200 and 98) respectively. If the gear (S) rotate with speed (450 r.p.m.) in C.W. direction and the gear (A) rotate with speed (100 r.p.m.) in C.C.W. direction, Determine the speed of the gear (P) and the arm (H). [Note: Start motion from gear (S)]. A Good Luck
A power transmission mechanism consists of a belt drive and a gear train as shown in the figure. Diameters of pulleys of belt drive and number of teeth (T) on the gears 2 to 7 are indicated in the figure. Find the speed and direction of rotation of gear 7 ? !187 2 N = 2500 rpm 150 mm 250 mm 36T 157 167 337 44T
The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to accelerate a flywheel at 0.1 rad/s2. The input gear has 11 teeth, and the output gear has 99 teeth. What is the flywheel's inertia? T=3N O O Input gear 11 teeth. Output gear 99 teeth 270 kgm² 57 kgm2 2.7 kgm2 Don't Know 27 kgm2 Flywheel 0.1 rad/s²
2- Figure (2) shows an epicyclic gear train suitable for lifting machine with the following particular: Gear A is the mounted on the motor shaft and the load spindle is attached to the arm 7. planet wheels C and Ci are compound. The number of teeth on wheels A and Ci are 20 The internal wheel B is fixed. A speed reduction of about 12 is required. Find the suitable number of teeth ror C and B and the exact value of speed ratio which these give. Z as
2) An electric motor transmits 0.5HP at 1600RPM. A 100 tooth helical pinion having a normal pressure angle of 25° and a helix angle of 15° and a normal diametral pitch of 10 teeth/in transmits power to a 100 tooth gear. Determine the tangential, radial and axial forces on the gear tooth.
Consider a planetary train in the figure below. The number of teeth of sun gear (2) is Z2 = 30, the number of teeth of planet gear (3) is Z3 =20 and the number of teeth of ring gear (4) Z4 = 70. Find the speeds of the planet gear (3) and the loader arm. The speeds of sun gear, w2 = 300 rpm, and ring gear w4 = 200 rpm are known.
The gear motor shown in Figure Q5(a) can develop 100W when it turns at 300 rpm. If the shaft has a diameter of 12 mm, determine the maximum shear stress that will develop in the shaft. Figure Q5(a)
ASAP
Please show your correct solutions to this Spur Gear problem neatly. Thanks. asap!