A sprocket with 200 teeth is the driver of a coal conveyer belt that operates at 60 rpm.You are to fit a new driven sprocket that must operate at 300 rpm or faster tomaintain the correct velocity of the coal belt.Formula: T₁ x N₁ = T2 x NzWhere: Ti is the number of teeth the driver.Ni is the speed (in revolutions per minute) of the driver.Ta is the number of teeth of the driven.N₂ is the speed (in revolutions per minute) of the driven.Calculate the number of teeth required for the driven sprocket.

The number of teeth required for the driven sprocket is T2 = 40 teeth.

A sprocket with 200 teeth is the driver of a coal conveyer belt that operates at 60 rpm. You are to fit a new driven sprocket that must operate at 300 rpm or faster to maintain the correct velocity of the coal belt. Formula: Tix N₁ = T₂ x N₂ Where: Ti is the number of teeth the driver. N is the speed (in revolutions per minute) of the driver. T₂ is the number of teeth of the driven. Na is the speed (in revolutions per minute) of the driven. Calculate the number of teeth required for the driven sprocket.

A sprocket with 200 teeth is the driver of a coal conveyer belt that operates at 60 rpm. You are to fit a new driven sprocket that must operate at 300 rpm or faster to maintain the correct velocity of the coal belt. Formula: Tix N₁ = T₂ x N₂ Where: Ti is the number of teeth the driver. N is the speed (in revolutions per minute) of the driver. T₂ is the number of teeth of the driven. Na is the speed (in revolutions per minute) of the driven. Calculate the number of teeth required for the driven sprocket.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. The force of a linear spring is given by F = kx, where F and k are the force on the spring and its stiffness, respectively. What is the dimension of k in the MLT system of units? a. M/L ML/T² b. F/L M/T² 4. A vehicle is running at 80 kph in a highway. If its wheel has a diameter of 524 mm, how fast is it turning in rpm. Assume that there is no slippage between the ground and the wheel. C. 742 d. 810 a. b. C. d. 565 675
Above is a 5 speed manual transmission gearbox. The gear selector fork is an assembly which the user requires in order to shift between gears thus moving the car with variable speed and torque outputs. Use the table provided below to find the following; Gear 1 2 3 4 5 RPM (N) 100 400 1200 3600 7200 Torque output (T) in (Nm) 2160 540 180 60 30 Determine the velocity ratio (gear ratio) between each gear (GR for gears; 1/2, 1/3, 1/4, 1/5, 2/3, 2/4, 2/5, 3/4, 3/5, 4/5).
Hide AnswerTry Another The formula for piston displacement is P = cd2SN, where c is a constant, d is the cylinder bore, S is the stroke, and N is the number of cylinders. For c = 0.7854, d = 3.000, S = 4, and N = 6, find the piston displacement. (Use the rules for working with measurements to give your answer to the appropriate accuracy and/or precision. Note: The values for S and N are exact numbers. Ignore exact numbers when determining the appropriate accuracy and/or precision.)
SOLVE CAREFULLY!! Please Write Clearly and Box the final Answer for Part A, with THE CORRECT UNITS ( should be ft/sec) Thank you. Express your answer to three significant figures and include appropriate units. DRAW the kinematic diagram and label it for this problem as well Thank you
In a rotating body, if it rotates at 2355 revolutions per minute.What would be the angular velocity ? the angular velocity of the rotating body in rad/sec is
Complete the following sentence. As the radius of curvature of a Cam gets smaller, the second derivative of follower displacement with respect to cam rotation: Select one: O a. none of these options O b. decreases O C. stays the same O d. increases 3 s page Next page 46 Finish Time le ps://learnonline.gmit.ie/mod/quiz/attempt.phplattempt-1670368cmid-1553068page-1. Type here to search
True Story! The 1998-1999 Mars Climate Orbiter mission was declared a total loss in1999 as there was a unit conversion mismatch error between Lockheed Martin and NASA. Themismatch was in the thruster force units. NASA used the SI system which called forNewton-Seconds (4.45 times as large) of thrust and Lockheed Martin used Pound-Force Seconds.Calculations placed the Orbiter at 68 miles from the surface as it went into orbit, but it waswithin 57 km of the surface after the breaking maneuver. Any distance from the surface lessthan 50 miles would have caused the Orbiter to crash.a. What was the actual distance of the Orbiter from the surface in miles?b. In percentage, how far off from the calculated 68 miles was the Orbiter?
1) From 0 to 10 sec, find alphaA1, alphaC1 in rad/s^2, omegaA1(t), omegaC1(t) in rad/s, thetaA1(t), thetaB1(t) and thetaC1(t) in rad, and the distance made by the load s1 in inches and in feet made by the load during this time.
A Cam-Follower system is sketched below (not to scale ); H=0.8 cm; D=3.0 cm; d=1.0 cm, R=1.0 cm, and w₂= 3 rad/s, what is the angular velocity of the roller (rad/s) ? (use Vector Graphical method)? O a. 3.00 O b. 7.92 O c. 4.50 O d. 6.18 e. 15.83 2 d (dia) Time left 0:47:02 R B D H- 13 3 1114 D (dia, Next page
Use Bayes’ Rule to solve the following problem: The new engine subcomponent was tested in two shifts. 60% of the tests were performed by the day shift and 40% of the tests were performed by the night shift. The tests pass 55% of the time during the day shift testing and 35% of the time during the night shift testing. The most recently tested component passed the test. What is the probability that is was tested by the night shift?
Compute the position and orientation of the tool point P from the given D-H table for the displacement variable e1-90° e2-90° and e3=90⁰ a1= 100 mm, a2= 100mm and a3 = 50mm Note: find the position and orientation using step by step procedure Figure 3 3-DOF (Industrial manipulator arm) Joint 0 d 1 01 0 2 02 3 03 0 0 Present the roll, pitch, yaw and displacement in x, y and z axis. use the composite transformation matrix [ce; -se,Cα; se; SÔ i-¹T₁ = 0 0 Sα₁ 0 CÔ Ca; co,ca; a a1 a2 az s0;Sα; se a | -90 0 0 Cα₁ 0 a;C0₁] –CĐ Sa, : aS0; a¡SO; d; 1
▼ Part A - Determining the magnitudes of the velocity and acceleration of the first driver Determine the magnitudes of the velocity and acceleration of the first driver. Express your two answers, separated by a comma, to two significant figures in meters per second and meters per second squared. ► View Available Hint(s) ΨΕ ΑΣΦ 11 vec S ? v₁. a1 = m/s m/s² Submit Previous Answers X Incorrect; Try Again; 3 attempts remaining 4 Part B - Determining the magnitudes of the velocity and acceleration of the second driver Determine the magnitudes of the velocity and acceleration of the second driver. by a comma, to two significant figures in meters per second and meters per second squared. 64.7, 14.5