A spring AB of constant k=200kn/m is attached to a support at A and to a collar of mass m=200 gm. The unstretched length of the spring is l=0.6m. Knowing that the collar is released from rest at x0 = 80 cm and neglecting friction between the collar and the horizontal rod, determine :the magnitude of the velocity of the collar as it passes through point C. www A

A spring AB of constant k=200kn/m is attached to a support at A and to a collar of mass m=200 gm. The unstretched length of the spring is l=0.6m. Knowing that the collar is released from rest at x0 = 80 cm and neglecting friction between the collar and the horizontal rod, determine :the magnitude of the velocity of the collar as it passes through point C. www A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

ww. E L d Vo В A bullet weighing 0.08 lb is fired with a horizontal velocity of 1800 ft/s into the lower end of a slender 15-lb bar of length L = 30 in. The slender bar is attached at E to an initially unstretched spring of constant k= 40 lb/ft as shown. Knowing that h=10 in and d= 25in. and that the bar is initially at rest. Using the impulse - Momentum principle, determine: %3D (a) the angular velocity of the bar immediately after the bullet becomes embedded. (b) the impulsive reaction at C Assuming that the bullet becomes embedded in 0.001s and the stretch distance of the spring is 2 in immediately after impact of the bullet.
A bullet (W₁ = 3.5 oz) with a is fired horizontally with a velocity v₁ = 1675 ft/sec into the block (W₂ = 5.7 lb) of soft wood initially at rest on the horizontal surface. The bullet emerges from the block with the velocity v₂ = 1280 ft/sec, and the block is observed to slide a distance of d = 7.3 ft before coming to rest. Determine the coefficient of kinetic friction μk between the block and the supporting surface. Answer: Uk= i W₁ W₂
A 10 kg block A rests on a smooth surface and the spring is compressed 0.1 m. It is attached to an inextensible cord over frictionless, weightless pulleys with a mass B of 24 kg, as shown. If the system is released from rest and B travels 0.1 m, what is A's speed? Consider K = 490N/m (spring) and VA = 2 x VB
I need the answer as soon as possible
3
Two masses, m1 and m2, are each suspended on identical springs. They were displaced an equal distance from equilibrium position and were released simultaneously. They are both at position of initial displacement at the instant m1 has completed 5 cycles and m2 has completed 3 cycles. m1=3 kilograms, determine the mass of m2 in kg
Collar A has a mass of 3 kg and is attached to a spring of constant 1200 N/m and of undeformed length equal to 0.5 m. The system is set in motion with r = 0.3 m, v0 = 2 m/s, and vr = 0. Neglecting the mass of the rod and the effect of friction, determine (a) the maximum distance between the origin and the collar, (b) the corresponding speed. (Hint: Solve the equation obtained for rby trial and error.)
N= 11.03N F= 25 N
A heavy goods vehicle of total mass 4.8 tonnes descends a hill with a gradient of 8 degrees from the horizontal. During this motion, the vehicle experiences a rolling resistance to its motion of 880 N. Whilst travelling at a velocity of 72 km/h, its brakes are applied, and the truck is brought uniformly to rest in a distance of 140 m. During this period of constant deceleration, it may be assumed that the rolling resistance remains constant at 880N, this being in addition to the retarding force applied by the brakes. Calculate for the vehicle whilst it is slowing down: a) The vertical height through which it descends. b) Its decrease in potential energy. c) Its initial velocity in m/s. Its decrease in kinetic energy.
A 5-kg collar can slide on a frictionless horizontal rod and is attached to a spring of constant k= 125 N/m. It is acted upon by a periodic force of magnitude F = F, cos wt, where Fo= 10 N and w = 5 rad/s. Determine the displacement and velocity of the collar at t = 0.2 s assuming that the initial conditions are zero. F = F, cos wt
Roller A, which has a mass of 2 kg is pushed by rod OC. If the angular velocity of the rod is 0.5 rad/s, determine value of the force exerted to the roller A, by the rod OC, when teta is equal to 600. The system is in vertical plane. Friction is neglected. A с 0 0,5 rad/sn 0,4 m