A spirally reinforced concrete column of size 400 mm diameter is subjected to a factored axial load of 1500 kN. The column has an unsupported length of 3.4 m and is effectively held in position at both ends, but not restrained against rotation. The reinforcement to be provided in the column using M25 grade concrete and Fe415 grade steel is (neglect steel area in compression)

A spirally reinforced concrete column of size 400 mm diameter is subjected to a factored axial load of 1500 kN. The column has an unsupported length of 3.4 m and is effectively held in position at both ends, but not restrained against rotation. The reinforcement to be provided in the column using M25 grade concrete and Fe415 grade steel is (neglect steel area in compression)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1.2m 10 cm O 7cm -7cm O This concrete beam has four A-35 steel rods of one centimeter diameter and a square cross section. It experiences a compressive axial load of 200kN. You must calculate the stresses developed in the two components in the figure.
A simply supported rectangular beam has a width of 300mm and an effective depth to the centroid of tension reinforcement of 330mm. The tension reinforcement has an area of 2843mm2 and the area of compression reinforcement placed 70mm from the compression face of the beam is 1231.5mm2, fy = 415MPa, fc’ = 30MPa. Balanced steel ratio is 0.031. The design strength using 0.90 as the reduction factor is ____kN.m
Wu-100 kN/m 6 m 4 m D Question 10 (PROBLEM 2) A three-member frame ABCD is loaded with ultimate gravity and lateral loads as shown in the figure. The compressive strength of concrete=21MPa, fy=415 MPa, beam width=300mm, beam height=600mm, main bar diameter=28mm, concrete cover=40mm, and stirrups diameter=10mm. Calculate the stress of compression reinforcement in the final section in MPa. B 4 m A mwm. Pu=115 kN
I already solve this question but I got wrong answer(Option A) Correct option is C. Please show me steps to how to get option C.... Please don't give me answer option A. thank you
6.
reinforced Concrete
A 8 m simply supported singly reinforced beam has a width of B= 39 cm and a height H=61 cm. Concrete compressive strength, f'c-30 MPa Steel Yield Strength of longitudinal bars, fyl-420 MPa, Steel Yield Strength of transverse bars, fyt -280 MPa, Unit weight of concrete, 24.4 kN/m³. Steel cover of the beam = 6 cm It is desired that the capacity of the beam to be at balanced condition. If the structural engineer wants the optimization ratio of the design moment and capacity to be 0.66, calculate the maximum value of the live load in kN/m to meet such condition Use NSCP2015
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the nominal moment capacity in kN∙m of the beam in negative bending.
A singly reinforced beam of dimension 200 x 350 is reinforced with 3-25mm at the bottom. If the concrete has a compressive strength of 17MPa and the steel has a yield strength of 415 MPa, determine if the beam can carry a uniform distributed load of 18 kN/m dead load. The beam has a length of 5m with 40mm concrete clear cover, 10mm enclosed stirrups, and Es = 200 GPa. Use LRFD in the analysis.
AT-Beam has the following properties: bf = 750 mm, bw = 275 mm, d 560 mm, t = 115 mm. Concrete compressive strength fe 21 MPa and steel yield strength fy 415 MPa. T-Beam is under factored moment load of 720 kN-m. Locate the compression block under balanced condition from the extreme compression fiber.