A sphere of mass 1.7 kg and radius 0.5 m is attached to the end of a massless rod of length 3.0 m. The rod rotates about an axis that is at the opposite end of the sphere (see below). The system rotates horizontally about the axis at a constant 272 rev/min. After rotating at this angular speed in a vacuum, air resistance is introduced and provides a force 0.18 N on the sphere opposite to the direction of motion. What is the power (in W) provided by air resistance to the system 107.0 s after air resistance is introduced? (Enter the magnitude.) Axis of rotation

A sphere of mass 1.7 kg and radius 0.5 m is attached to the end of a massless rod of length 3.0 m. The rod rotates about an axis that is at the opposite end of the sphere (see below). The system rotates horizontally about the axis at a constant 272 rev/min. After rotating at this angular speed in a vacuum, air resistance is introduced and provides a force 0.18 N on the sphere opposite to the direction of motion. What is the power (in W) provided by air resistance to the system 107.0 s after air resistance is introduced? (Enter the magnitude.) Axis of rotation

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A relatively thin disc with uniformly distributed mass is mounted on a shaft which rotates at 1000 RPM. To conduct a test, two extra masses are added to the disc at the positions shown in Figure Q10. Masses A and B introduce known unbalances of 2 kgmm and 4 kgmm, respectively. Determine the angular location of the correction mass measured from y-axis in the clockwise direction and the centrifugal force that it needs to produce in order to balance the system. YA A 30° B 70° X TIT TIT N
Solve the problem quick and correctly , Urgent. Thanks....
A box of mass m = 0.7 kg is attached to a rope which is wrapped around a physical pulley with a radius of R = 10.2 cm and a rotational inertia of I = 0.075 kg·m2. When the box is released it starts to fall down with a constant acceleration and, at the same time, the pulley starts to spin up, see the picture below. Assuming that the pulley is frictionless, what is the magnitude of the box's acceleration and what is the tension in the rope? The acceleration of the box, a ? The tension in the rope, T? If the box starts from rest and traveled downwards a distance of h = 28 cm, what is the speed of the box and what is the angular velocity of the pulley? The speed of the box, v =? The angular velocity of the pulley, ω? -------------------------------------------------------------- A Merry Go Round carousel has a radius of R = 2.4 m and a rotational inertia of I = 695 kg·m2. A 75‑kg student is on the carousel at the midpoint between the carousel's center and the rim (at R/2 distance from…
Problem No. 8 A shaft rotating at 120 rev/min is supported in bearings C and D, 1.8 m apart. Two unbalanced rotating masses of 7.5 kg and 10 kg at radii of 7.5 cm and 5 cm respectively are situated between C and D at distance of 0.6 and 0.9 respectively from C. the angle between the radii is 60°. Find the magnitudes and directions of the forces of the shaft on the bearings due to the combined action of the inertia loads (dynamic) and gravity forces (static) at the moment when the 7.5 kg is vertical and above the shaft and the 10 kg mass is on the right of the 7.5 kg mass when viewed from D to C.
. An object of mass 12 kg is suspended from a pulley which has a mass of 6 kg and a radius of rotation of 0.25 m. If at that time the pulley rotates with an angular velocity of 5 rad/s, we want to know that when the object moves down a distance of 2 m, then at what speed is the pulley rotating? If the friction force on the pulley bearing produces a moment of resistance of 2 N-m 12 kg 0.3 m
The mass of a propeller is 4.5 tons and its centre of gravity is 3.5 mm from the centre of rotation. Find the pull due to centrifugal force when it is rotating at 120 rev/mm
Consider a uniform ladder of length 4.3 m and mass 10 kg. The ladder is falling over, pivoting about the end that is touching the ground. Someone is pushing on the top end of the ladder with a horizontal force of size 415 N. At the instant when the ladder makes a 46 degree angle with the horizontal, calculate the net torque on the ladder about its bottom end, in N m. Make your answer positive, and use g = 10 m/s2. (Please answer to the fourth decimal place - i.e 14.3225)
A spur pinion of pitch diameter 50 mm rotates at 200 rad/s and transmits 3 kW power. The pressure angle of the tooth of the pinion is 20°. Assuming that only one pair of the teeth is in contact, the total force (in Newton) exerted by a tooth of the pinion on the tooth on a mating gear is
Question 3 The speed of the engine mechanism shown in Figure 1 is controlled by the Porter governor. All arms of the governor are 20 mm and are hinged at a distance of 4 mm from the axis of rotation. The mass of each ball is 100 g and the mass of the sleeve is 500 g. The governor sleeve begins to rise at 40 rad/s. when the links are at an angle of 5° to the vertical. Assuming the friction force to be constant 3.1. Draw the port governor mechanism and clearly lable it. 3.2. Calculate the minimum speed of rotation (in rad/s) when the inclination of the arms to the vertical is 10°.
4 -(Kinetics of Curvilinear Motion) Tow weights W, and W2 of 8KN and 5KN are attached at the ends of a flexible cable. The cable passes over a pulley of 100 cm diameter. The weight of the pulley is 600N with a radius of gyration of 50cm about its axis of rotation. Find the torque which must be applied to the pulley to raise the 8KN weight with an acceleration 1.5 m/s?. Neglect friction in the pulley bearing. 50 cm 600N T 8kN 5kN W,
Q2
For the mechanism shown in the figure, find the accelerations of the connecting rod at its center of gravity. When the crankshaft rotates at a constant speed at 3500 rpm, and when it accelerates uniformly from 1000 to 4000 rpm. The center of gravity of bar 2 is 11 cm from the joint with bar 1. bar 1=12cm bar 2=32cm 2