A source register is read during the instruction's execution, while a destination register is written during the instruction's execution. Define which of the following MIPS instructions are source registers and destination registers. Figure 1 add $t1, $t2, $t3 add $t1, $t1, $t1 addi $t3, $zero, 1000 lw $t2, 16($gp) sw $t2, 4($s5) bne $s1, $s2, loop1

Q: ID/EX EX/MEM Control IF/ID Add Branch Add- Shift left 2, RegWrite Read Addr 1 Register Read Read…

A: Register ID/EX stores 3 control signals(ALUSrc, Branch, MemtoReg), (PC + 4)(32-bits), register1…

Q: In the following instruction sequence, show the value of AL for each line of code. Write the value…

A: Instructions Value of AL(H) MOV AL, 01100001B AND AL, 00011101B 1H MOV AL, 12H MOV AL,…

Q: Assume AL=35h; CL=05. Write the content of AL after RCR AL, CL - showing the calculation steps.…

A: RCR : rotating the bits right side through carry. Syntax : RCR dest , count

Q: Using the following data definitions: byte1 BYTE OFFh, 1, 2 byte2 BYTE 14h OFFFFh, 1, 2 word1 WORD…

A: Using the above data definition we need to write instruction which moves the lower 8 bits of word2…

Q: General purpose register EAX contains internal code (hexadecimal): 00020FFF General purpose register…

A: we have an EAX register which can be represented as:-     AH AL The highlighted part comes…

Q: Q3/ Initially assume all flags are set, find the values of status flags and AL after each…

A: Status Flags: Bits in a register indicating results or status of arithmetic/logical operations.AL…

Q: Select the value of AL after the following rotate instruction is executed: mov al, 0D4h rol al, 1…

A: Here is the explanation about the rotation:

Q: Q:find the actual address for the following instruction assume X=A6 and ?=PC=8B79, LOAD X(PC), D…

A: The given data is. X = A6 PC = 8B79 The given instruction is: LOAD X(PC), D

Q: Write the execute cycle of the instruction “ADD E” in Register Transfer Notation

A: Instruction execution cycle involves following steps, fetch decode Execute store The above…

Q: In the field below, enter the integer value of the $v0 register after executing the following…

A: Given $zero=0 , $at=44 . We have to find the integer value of the $vo register after executing the…

Q: answer all the questions

A: Here we have to answer all the given MCQs

Q: Write the execute cycle of the instruction "ADD E" in Register Transfer Notation.

A: write the Execute cycle of the instruction ADD E in register Transfer notation. Answer Execute…

Q: True or False: An inclusive OR (OR) instruction generates the value true if either (but not both)…

A: The given statement is False An inclusive OR (OR) instruction, also known as the logical OR,…

Q: When the j or jal instruction executes, what is the maximum jump distance

A: Correct answer is: Approximately 67 thousand instructions in either direction

Q: The execution cycle of an instruction can be described using Register Transfer Notation by writing…

A: Intro The instruction execution cycle comprises the following steps: Fetch Decode Execute Store The…

Q: You are given the initial values of the following registers: eax = 0x00000011, ebx = 0x1234ABCD, ecx…

A: Dear Student, The first instruction, "mov ah, 5Bh", moves the value 5Bh into the ah register. eax =…

Q: 2- Show how each of the following MIPS instructions is converted into machine code. Assume the…

A: Actually, given question regarding MIPS instructions.

Q: A-The 8086 LOOP instruction decrements register Cx__and Tests it for a 0 to decide if a jump occurs.…

A:

Q: Q:The registers that are essential in memory write and read operations (which of the following…

A: NOTE  :-  As per our guidelines we are supposed to answer  only one question. Kindly repost other…

Q: Q:find the actual address for the following instruction assume X= (27)hex and R index=DBC9 LOAD…

A: Question:

Q: Q2. Design a control logic to implement the following register transfer statements assuming that…

A: Please check the step 2 for solution.

Q: For the following instruction: sltu $s0, $t2, $t3 what the content of the register ($s0) after…

A: - We need to show the value of $s0 register.

Q: Given the statement, R = J +O +K- E, write the instruction using I address instruction format.

A: Your question is about 1 address instructions.  Let's solution for you.

Q: Table 4 is showing the address location of the instructions stored in the memory. Please refer to…

A: i) Traps vectors used: First identify the TRAP instructions using the opcode 1111 and then convert…

Q: In the field below, enter the integer value of the $v0 register after executing the following…

A: addiu" is an instruction in  MIPS assembly language instruction that stands for "add immediate…

Q: Question 39 It is an instruction to clear the register. A XOR AX,AX B CLC CLEAR

A: The XOR gate is the logic gate that gives a true value when the inputs are different. The process of…

Q: 45": add $a0, $zero, $zero

A: given -  What single MIPS instruction (replacing the comment in line 3) will complete the following…

Q: The Fetch step of the instruction cycle loads the instruction stored at the program counter and puts…

A: In the field of computer architecture and central processing units (CPUs), the instruction cycle is…

Q: CMP INSTRUCTION HAS THE SAME FUNCTION AS Select one: a. SUB INSTRUCTION WITH SAVING THE RESULT IN…

A: Let us see the answer below.

Q: QI) I BX=1000, DS-0200, SS=0100, CS-0300 and AL=EDH, for the following instruction: MOV [BX] +…

A: Here is Solution for Above Problem  :: Q1). Given Data : BX = 1000 DS = 0200 SS = 0100 CS = 0300 AL…

Q: H\W: assume Ds- 2400, show the content of register as each the following instruction execute Μον Bκ,…

A: Given: MOV Bx, 1357hMOV SI, 1234hLES DI, [Bx][SI] To find: To find the content of the register from…

Q: If PC=62 when the instruction BSA 831 is executed, What is the contents of AR and PC locations…

A: BSA instruction is a subroutine call . This is used to create branching operation for the…

Q: True/False The opcode field of the instruction affects the value of the control signals used to…

A: According to the information given:- We have to find out the mentioned statement is true or not.

Q: Data operation stage is happening after the operand address calculation in the instruction cycle.…

A: Instruction Cycle will, fetch stage, decode stage, execute stage.

Q: In this instance, the operand would be the Instruction Register (IR).

A: What is register: A register is a small storage area in a computer's central processing unit (CPU)…

Q: Assume AL=23h; CL=05. Write the content of AL after ROL AL, CL- showing the calculation steps.…

A: STC instruction will set the carry flag initially.

Q: The range of jump instruction is more than branch instruction. Select one: True False

A: i have provided answer in step2.

Q: Segment registers hold O a. neither the starting address nor the ending address of the segment O b.…

A: Paging technique doesn't give an user the idea of how program is stored onto memory.  This program…

Q: Fill in the following table showing the results of the indicated instructions, using the register…

A:

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.