A solid steel column and a hollow steel column, both have the same length and same cross-section area, and are fixed at the ends. If the internal diameter of hollow column is 2/3 of its external diameter, find the ratio of buckling strengths of solid steel column to that of hollow steel column.

A solid steel column and a hollow steel column, both have the same length and same cross-section area, and are fixed at the ends. If the internal diameter of hollow column is 2/3 of its external diameter, find the ratio of buckling strengths of solid steel column to that of hollow steel column.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solution w/FBD
axial compressive force P. If the stress on steel snugly fitted on a solid steel rod of 20 mm A tube of aluminium of 40 mm external diameter and 20 mm internal diameter diameter. The composite bar is subjected to a bar is 70 N/mm", the stress in the aluminium tube and corresponding value of P will be: E for steel: 2 x 10 N/mm and E for aluminium 7 x 10ʻ N/mm')
An SSTM A36 strucural steel beam 3.6 m long is placed between two rigid supports when the temperature is 15 0C. What is the stress developed in the beam if the temperature rises to 50 0C? ___ MPa. Assume that the proportional limit is 235 MPa, and that lateral buckling is prevented. Calculate your answer to 1 decimal place.
The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
The solid rod has a diameter of 20mm. Find the following: Angle of twist at C with respect to A (in radians) Angle of twist at B with respect to A (in radians) Maximum shear stress at A (in MPa) (Shear stress at support, at a point 7mm from center. (in MPa) A-36 steel with the following properties: Modulus of Elasticity, E = 29x10^3 ksi or 200 GPa Shear Modulus/Modulus of Rigidity, G = 11.5x10^3 ksi or 79.3 GPa Poisson's Ratio, nu = 0.260 Temperature Coefficient for thermal expansion, a = 6.6x10^-6/°F or 11.7x10^-6/°C
1
When designing a structural member, which of the following statements is FALSE? A. The allowable stress is used in calculating the maximum load to be applied. B. The ultimate stress depends on the Factor of Safety used. C. The ultimate stress is determined based on the material used. D. The allowable stress depends on how conservative the design is. Which of the following is NOT a valid reason for increasing the Factor of Safety? A. Higher uncertainty in loading conditions B. Higher design life C. Lower confidence in assumed/stated material properties D. Lower member importance Consider a 1,000-mm long, 25-mm diameter sample subjected to a tension test. Automatic high-precision gages recorded that for an applied load of 150 kN, the sample experienced a longitudinal strain of 2×10−3mm/mm. Assuming that the material remained elastic while loaded, determine its modulus of elasticity. A. 175.0 GPa B. 63.7 GPa C. 152.8 GPa D. 72.9 GPa
An aluminum alloy bar (E = 72 GPa) has length L = 2m, constant thickness t = 20mm, and a rectangular cross section whose width varies linearly between b2 = 115 mm at the fixed support to b1 = 100mm at the free end. Assume that the taper of the bar is small. If P2 = 200kN, hwta is P1 so that the displacement tc=0. What is the displacement tb?
A cantilever beam with cross section shown below and span of 3 m is subjected to concentrated load (P) at the free end. If the maximum allowable tensile stress equals to 10 MPa what is the maximum value of the load P can be applied.
A mild steel flat of width 120 mm and thickness 10 mm is bent into an arc of a circle of radius 10 m by applying a pure moment 'M'. If E is 200 GPa, then magnitude of the pure moment 'M' will be
A rectangular steel block is 3.0 inches long in the x-direction, 3.0 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 50 kips tension in the x-direction, 60 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places
value for modulus of elasticty for steel is 29000 ksi and for aluminum it is 10000ksi. yield strength for steel is 36 ksi and yield strength for aluminum is 37 ksi