A solid shaft with a constant cross sectional area is subjected to twisting moment as shown. The shaft has a diameter of 64 mm and a shear modulus of 64 GPA 1. Which of the following most nearly gives the reaction at the fixed end? a. 1800 N.m b. 1000 N.m c. 1200 N.m d. 1400 N.m   2. Which of the following most nearly gives the maximum shearing stress in the shaft?  a. 29.48 MPa b. 39.53 MPa c. 49.44 MPa d. 19.43 MPa

Q: If the allowable shear strength of aluminum is 45 MPa, determine the minimum thickness, t, of the…

A:

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A:

Q: A machine shaft supported on bearings 11 ft apart is to transmit 288hp at 200 rpm while subjected to…

A:

Q: 5. A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12 ksi. If the…

A:

Q: 4. The tapered shaft is made from E- 36 steel (G = 80 GPa ), and has a radius which can be described…

A: Given    Torque, T = 450 Nm    Length, L = 4 m Find     Angle of the twist

Q: must transmit the torque of 34 kN-m. The total angle of twist must not exceed 3°. The maximum…

A:

Q: The torque transmitted by a solid shaft of diameter 10 mm and shear stress 75 MPa  Select one: a.…

A: Given data: Diameter of the solid shaft, D= 10mm Shear stress, s=75MPa=75N/mm2

Q: 4. A steel shaft 4 ft long that has a diameter of 5 in is subjected to a torque of 20 kip-ft. Use a…

A:

Q: 2. In the gear system shown, the motor applies a torque of 600 N-m to the gear A. Shafts (1) and (2)…

A:

Q: solid steel shaft is made of steel has 100-mm diameter. The shaft is subjected to the distributed…

A:

Q: The copper shaft is hollow from A to B and the steel shaft is solid from B to C. The shaft has an…

A: Given that, Outer diameter of shaft, Do=100 mm,Thickness of shaft, t=20 mm,Modulus of rigidty of…

Q: A solid steel shaft will not twist through more than 3 degrees in a 6-m length when subjected to a…

A: Given data: The angle of twist, θ=3°. The length of shaft, L=6 m. The applied torque, T=12 kN·m.…

Q: A certain circular shaft is subjected to a maximum equivalent bending moment of 36,000 in-lb and a…

A:

Q: E' 3. For the 3-in.-diameter solid cylinder and loading shown, T = 40 kip-in., determine: (a) the…

A:

Q: What is the correct formula for the maximum shearing stress in case of shaft with diameter d and…

A:

Q: 3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B…

A:

Q: An aluminum rod AB of diameter 2.8 inches is connected to a lever of length L = 5.6 feet. Consider…

A: Given:diameter, d=2.8 inL=5.6 ftheight, H=3.4 ftTorsional shearing stress of aluminium, ζa=1111 psi

Q: hollow brass (6000 ksi) shaft CD and a thin-walled steel (G=12000 ksi) tube DE. The whole assembly…

A: Find out:Maximum shear stress in the bolts at C (ksi)Maximum shear stress in the bolts at D (ksi)The…

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A: Given: The allowable shearing stress in the shaft, τ = 55 MPa The length of shaft AB, LAB = 750 mm =…

Q: Q2/A solid circular transmission shaft of (2m) long with angle of twist not exceed (39) which used…

A: Given,Length of the shaft (L) = 2 mThe angle of twist (θ) = 3° = 0.052 radiansPower  P = 2.5 hp =…

Q: the torque acting on the shaft; ii) the required external and internal diameters for the shaft;…

A:

Q: PROBLEM NO. 2 A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in…

A: Given data: ◆ The bolt circle diameter: D = 250 mm ◆ The number of bolts: n = 12 bolts ◆ The…

Q: The solid shaft shown is formed of a brass for which the allowable shearing stress is 55 MPa.…

A: if you have any doubts please comment

Q: Select the size of a hollow steel shaft necessary to transmit 150 hp at 250 rpm without exceeding an…

A: Given data,    Power=150hp    speed=250 rpm    shear stress=4.7ksi    angle  of twist =0.35°…

Q: 1. The solid line shaft in Fig. 1 is made of steel and transmits the input power of 35 kW at pulley…

A: The Answer is Below

Q: (a) For the solid steel shaft shown, determine the angle of twist at A. Use G=11.2 × 106 psi. (b)…

A: Given data: The applied torque is, T = 60 kipˑin. The inner diameter, di = 0.75 in. The outer…

Q: Q5: Determine the diameter of the solid shaft where the angle of twist not exceed 10 and the length…

A: Given: The angle of the twist: →θ=1°=1×π180=0.017 radian Diameter of the shaft=d And length of the…

Q: Q.191 A solid circular shaft of diameter 100 mm is loaded with a uniformly distributed torque of 4…

A:

Q: ix 30 mm diameter bolts in the outer bold circle of 370 mm radius are steel and six 20 mm diameter…

A:

Q: A compound shaft consists of two solid shafts that are connected at flange B and attached to rigid…

A:

Q: Determie the rotation or twist in degrees of a shaft, 742 mm long subjected to a torque of 95 N-m,…

A: According to the given datawe need to findThe angle of the twist

Q: a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa,…

A: for solution refer below images.

Q: The torque T causes a rotation of 2° at end B of the stainless-steel bar shown. Knowing that b = 20…

A: The rotation of the bar is .The distances are given as-The length of the bar is .The shear modulus…

Q: 5. Two shafts (G = 50 GPa) with different diameters are bonded to a disk in the middle. The ends A…

A:

Q: The motor on the left provides a torque of 5500 N•m to the gear shaft shown. The motor runs machines…

A:

Q: The composite shaft shown consists of two steel pipes that are connected at flange B and securely…

A:

Q: 18.From the Fig.(3). A thin walled tubeis constructed from aluminium alloy with shear modulus G = 30…

A: Given Datar=75mmt=1mmG=30GN/m2 As in question there is not given torque and whole length…

Q: 64. A solid circular shaft of diameter d and length L is fixed at one end and free at the other end.…

A: A solid circular shaft-Diameter = dLength = LFixed at one end & free at other.To Find-The value…

Q: Determine the maximum shearing stress in a helical steel spring composed of 20 turns of 20-mm…

A:

Design of Shafts and Shaft Components

The shaft is basically defined as the machine element that rotates, is in circular cross-section, it is majorly used to transfer the power from one part of the system to another, or from a power generating machine to a power absorbing machine. The shaft is supported on bearings and is rotated with the help of a set of gears or pulleys that are used for the power transmission. Bending moment, torsion, and an axial force act upon the shaft. Designing of shaft primarily involves determining stresses at a critical point in the shaft that is arising due to loading.