A solid shaft and a hollow shaft are to be of equal strength in torsion. The hollow shaft is to be 10% larger in diameter than the solid shaft. What will be the ratio of the weight of the hollow shaft to that of the solid shaft? Both shafts are to be made of the same material. Ans. The hollow shaft will weigh 0.6 that of the solid shaft.

A solid shaft and a hollow shaft are to be of equal strength in torsion. The hollow shaft is to be 10% larger in diameter than the solid shaft. What will be the ratio of the weight of the hollow shaft to that of the solid shaft? Both shafts are to be made of the same material. Ans. The hollow shaft will weigh 0.6 that of the solid shaft.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. You are to design an axially loaded member that is to carry a load of 5,000 lb. The member is to be made of ASTM A36 steel and have a total length of 24 in. Due to the design requirements the maximum allowable elongation of this member under the stated load is 0.025 in. Find the smallest allowable diameter of the member. a. Given: PL where ô is member elongation, P is axial load, L is initial member length, E is the material's Modulus of Elasticity, EA and A is the member's cross section area E136 = 29*10° psi (Beer, 746)
Strengon of Mace Question Tas Preasure esse The hoop stress on the walls of a thin cylinder is 42 MPa. The diameter of the cylinder is 84 cm and the thickness is 1.5 cm. What is the internal pressure of the cylinder?
please show a step by step solution, thank you A steel shaft with diameter of 40mm can transfer a 32.5 kN-m torque force. What is the shaft's lowest minimum stress, measured in MPa? Answer in 4 decimals
1. Find a.b and c for the following hollow axis. ( Must use Tresca Critetton.) Mt Tnner dia meter : ri Mt outside diameter : r. a) Maxrmum Zae, b) Mt that the Thitial yielding wil be initiated c) Mt that the axīs will be destroged (The yield stress Th the tensīle test is Y)
Solve the problem. 1. You are using a wheel and axle as a simple machine. You applied a force of 30 lb to the rim of the wheel so that it can lift a load of 240 lb. The diameters of the wheel
Please answer asap. Thank you Note: Tolereance is ± 1 in the 3rd significant digit. Exact answer. This is a by part qustion so please answer all necessary points or joints in the problem. Thank you. I will rate you accordingly
. A 102 mm diameter shaft is driven at 3000 rpm by a 250 Hp motor.The shaft drives a 121.9 cm diameter chain sprocket. Compute thetorque in kN.m
You rejected the question, but the question already asks for internal and external diameter values. Please solve this.
The external torque on a drill bit varies linearly to a maximum intensity q, in.Ib/in . If the drill bit diameter is d, its length L, and modulus of rigidity G Determine the relative rotation of the end of the drill bit with respect to the chunk.
A solid steel shaft 5 m. long is stressed to 60 MPa when twisted through 4° (degrees). Using G = 83 GPa, compute the shaft diameter. Convert your answers to mm.
* Problem-based learning - Acquire enhanced problem-solving skills using critical thinking Two shaft 40 mm of diameter are connected by a flanged coupling. The flanges are fitted with 8 bolts on 140 mm bolt circle. The shafts transmit a torque of 900 N-m at 350 r.p.m. For the safe stresses mentioned below, calculate 1. diameter of bolts ; 2. thickness of flanges ; 3. key dimensions ; 4. hub length; and 5. power transmitted. Safe shear stress for shaft material = 63 MPa Safe stress for bolt material = 56 MPa Safe stress for cast iron coupling = 10 MPa Safe stress for key material = 46 MPa A belt 100 mm wide and 10 mm thick is transmitting power at 1000 rev/min while the large pulley rotates , The larger pulley diameter is 1 .8 times the smaller pulley which having 250 mm diameter. Calculate the maximum power that can be transmitted. When the distance between the two pulleys are 4 m
find the displacements at the inner radius of a long cylinder of inside diameter 80mm and outside diameter 120mm snugly fits in a hole over its full length. The cylinder is then subjected to an internal pressure of 2MPA. Using two elements on the 10mm length.