A solid plastic rod has a diameter of d = 34 mm and a length of L = 500 mm. An axial load of P = 34 kN is applied to the rod as shown. The elastic modulus is E = 2.5 GPa and Poisson's ratio for this material is v=0.40. Determine the magnitude of the change in the rod diameter Ad for the given load.

A solid plastic rod has a diameter of d = 34 mm and a length of L = 500 mm. An axial load of P = 34 kN is applied to the rod as shown. The elastic modulus is E = 2.5 GPa and Poisson's ratio for this material is v=0.40. Determine the magnitude of the change in the rod diameter Ad for the given load.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For a steel plate, whose length (along the y-direction) is very large compared to its width (along the x-direction), the deflected surface is assumed to be cylindrical; the axis of the cylinder is parallel to the length of the plate. At a certain point, the strain in the shorter direction was measured as 0.0066. Taking E =255 x 103 N/mm2, Poisson’s ratio n = 0.3; Calculate the stresses σx & σy.b) Explain why in-plane forces are neglected in the analysis of bending in thin plates
The stress concentration occurs whenever there is an abrupt change in the cross-section of a component or there is any discontinuity in the material. The figure given below shows a flat plate with a hole of diameter d. The plate is fixed at one end and the other end is subjected to a tensile load of P = 44 kN due to which there is a change in length of 0.4 mm. The thickness of the plate is 11.5 mm. The maximum stress developed in the flat plate is 228 MPa. Take Young's modulus(E) = 210 GPa and theoretical stress concentration factor =2, Calculate the following values: i) Width of the plate (W2) in mm ( ii) Nominal Stress in MPa ( iii) Diameter of the hole (d) in mm
M A cylinder of outer radius R2=100 mm is fitted on another cylinder of outside radius R₁=85 mm with thickness t=30 mm, as depicted below. If the (tensile) maximum hoop stress at the interface between the two cylinder is 90 MPa, solve the following questions (E=105 MPa and v=0.15). === R₁ What is the radial stress between the cylinders? What is the shrinkage allowance at the interface? ( M R₂ )
Bars (1) are made of a polyimide plastic that has an elastic modulus of 4.4 GPa. Bar (2) is a nylon material that has an elastic modulus of 1.3 GPa. Each bar has a cross-sectional area of 1100 mm². Using L=335 mm and A = 6.4 mm, what magnitude of load P will cause the normal stress in each bar to be the same value? a (1) Answer: P = i B C (1) kN
Bars (1) are made of a polyimide plastic that has an elastic modulus of 3.7 GPa. Bar (2) is a nylon material that has an elastic modulus of 0.9 GPa. Each bar has a cross-sectional area of 1350 mm². Using L = 355 mm and A = 6.3 mm, what magnitude of load P will cause the normal stress in each bar to be the same value? a (1) Answer: P = i B C (1) KN
In the figure, determine the normal stress and change in length of the aluminum rod if the temperature was raised by 126°C. The 0.5-mm gap exists at 25°C. 0.56 mm 366 mm 255 mm Aluminum A = 2TTT mm² E = 75 GPa x = 23 x 10*/°C B Stainless Steel A = 8QQ mm² E = 190 GPa α = 17.3 x 10/°℃
The stress concentration occurs whenever there is an abrupt change in the cross-section of a component or there is any discontinuity in the material. The figure given below shows a flat plate with a hole of diameter d. The plate is fixed at one end and the other end is subjected to a tensile load of P = 41 kN due to which there is a change in length of 0.4 mm. The thickness of the plate is 11 mm. The maximum stress developed in the flat plate is 235 MPa. Take Young's modulus(E) = 210 GPa and theoretical stress concentration factor =2, Calculate the following values: i) Width of the plate (W2) in mm ii) Nominal Stress in MPa iii) Diameter of the hole (d) in mm Hole with stress concentration factor 2 35 mm W2 35 mm P 300 mm 350 mm- 250 mm
A steel wire (E = 200 GPa) of diameter d = 1.0 mm is bent around a pulley of radius Ro= 400 mm (see figure below). Ro a. What is the maximum stress in the wire? b. Does the stress increase or decrease if the radius of the pulley is increased?
12. two decimal places
THERMAL STRESS 3. A rigid bar is supported by two copper rods and the gap between the aluminum rod and the bar is 1.50 mm. If the temperature for all materials is increased by 40 degrees Celsius, will the aluminum rod touch the rigid bar or not? Prove your answer. For each copper bar, A = 500 mm^2, E = 120 GPa and a = 16.8 um/(m C). For the aluminum bar, A = 400 mm^2, E = 70 GPa , and a = 23.1 um/(m C).
a. Calculate the ductility of the sample as a percentage (%) b. Calculate the stress required to create a neck in the sample, in MPa.
ASAP, please solve it now. Reject it if you cannot answer now. Thank you. The bar ABC in the figure consists of two cylindrical segments. The material of the bar has the stress-strain diagram shown. Calculate the: a. stress in segment BC caused by the 60-kN axial load b. strain in segment BC caused by the 60-kN axial load c. elongation in segment BC caused by the 60-kN axial load