A solid constant-diameter shaft is subjected to the torques shown in the figure. The bearings shown allow the shaft to turn freely. a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. b) If the ultimate shear stress in the shaft is 320MPa and the F.S. of 4, determine the minimum acceptable diameter for the shaft. 110 N-m 330 N-m

A solid constant-diameter shaft is subjected to the torques shown in the figure. The bearings shown allow the shaft to turn freely. a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. b) If the ultimate shear stress in the shaft is 320MPa and the F.S. of 4, determine the minimum acceptable diameter for the shaft. 110 N-m 330 N-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8. The cross section of the machine part is a square, 5 mm on a side. If the maximum stress at section m-n is limited to 150 MPa, determine the largest allowable value of the eccentricity e. 250 N 250 N
Note: hand written solution is not allowed.
c2
An aluminum tube of outer diameter R, = 50 mm is heated such that it is mounted over a steel shaft of radius, R, = 30 mm as shown in the figure. The length I of member is 3 m. MT R Ri If a G, = 77.2 GPa G, = 27 GPa and torque of M- = 76 kN. m S appirec o rdICE TWISting in the memper Determine the maximum shear stress in the tube
Situation 5 A steel shaft with a constant diameter of 50 mm is loaded as shown by applied torque. Use G=83 GPa. Solve for the total angular deformation. 800 N-m 1300 N-m 1200 N-m 2 m 1.5 m 3 m
The 54-mm-diameter solid shaft is made of 2014-T6 aluminum and is subjected to the distributed and concentrated torsional loadings shown where T = 1.75 kN.m. (Figure 1) Figure 04m 0.6 m, 2 kN-m/m 1 of 1> Determine the angle of twist at the free end A of the shaft. Express your answer in degrees to three significant figures. 6 = 17 ΑΣΦ ↓↑ Submit Provide Feedback Request Answer vec ?
3 - A torque of 2000 N-m is applied on a steel circular shaft with a diameter of 50 mm. The shaft has a length of 2 m. The Young's modulus and Poisson's ratio of the steel are E = 200 GPa and ✓= 0.3, respectively. What is the maximum shearing stress? What angle of twist occurs over the length of the shaft?
Part 2,3,4
Qus
Q-1 A circular bar is to withstand a bending moment of 10 kNm and a torque of 30 kNm. Determine the diameter of the bar if the yield stress of the material is 250 MPa and the factor of safety is 3. Use maximum normal strain theory of failure. Take Poisson's ratio as 0.3.
2.0 in 3.0 in. The tubular torsional shaft shown above is made ofa stainless steel metal with the following properties: E = 28500 ksi • G= 11000 ksi • v = 0.37 If the pipe cross-section is subjected to an internal torque of T 50 kip-in, which of the following is closest to the minimum shear stress action on the cross-section? 3.92 ksi 1.57 ksi 7.84 ksi
The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tcircle/Tsquare of the shear stresses. Given: r = 11 mm, S = 20 mm, and t = 2.58 mm. %3D S. S. ENG us