A solid circular bronze [G = 6,500 ksi] shaft, 4.6 ft long and 1.575 in. in diameter, carries a torque of 60 lb-ft. For this shaft, determine (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax = psi (b) Ф%3D Save for Later Attempts: 0 of 1 used Submit Answer

A solid circular bronze [G = 6,500 ksi] shaft, 4.6 ft long and 1.575 in. in diameter, carries a torque of 60 lb-ft. For this shaft, determine (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax = psi (b) Ф%3D Save for Later Attempts: 0 of 1 used Submit Answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A solid 1.500-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 190 lb-ft and TD= 140 lb-ft, acting in the directions shown. Assume a = 42 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 20 ksi, determine the maximum torque TC that can be applied to the shaft.
A steel shaft with a diameter 45 mm and length 1.30 m transmits 55.50 kW from an electric motor to a compressor. The allowable shear stress is 51.75 MPa and the allowable angle of twist is 2.1 degrees. G=83x10^3 psi Determine the polar moment of inertia (in mm^4) of the steel shaft. Determine the required torque (in N-m) as limited by stress. Determine the required torque (in N-m) as limited by the angle of twist.
Please answer complete
The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque T (in Nm) that can be applied to the ends of the shaft without exceeding a shear stress of 70081031 Pa and angle of twist of 2.31°. Use G= 83000000000 Pafor the shaft, x = 2.5 m, and y = 1.71 m. Round off the final answer to two decimal places. T ... 100 mm 70 mm 70 mm T y
3. A solid circular shaft is 1.8 m and is made of steel with G = 70 GPa. When rotating at w = 70 rad/s, it transmits 28 kW of power from engine A to generator B. As the design engineer, you are asked to: (a) Determine the shaft's smallest allowable radius if the allowable shear stress is T allow = 80 MPa. (b) Determine the shaft's smallest allowable radius If the allowable angle of twist is allow = 0.1 rad (in other words, the shaft is restricted not to twist more than 0.1 rad). (c) If both conditions (a) and (b) are required simultaneously, which radius will you select as the allowable radius. (In other words which condition controls the situation)? Briefly explain your answer. (1 kW = 1000 Watts) B
A solid 2.9-in.-diameter bronze [ G = 7100 ksi] shaft is 8-ft long. The allowable shear stress in the shaft is 10.2 ksi and the angle of twist must not exceed 0.034 rad. Determine the maximum horsepower P that this shaft can deliver: (a) when rotating at 182 rpm. (b) when rotating at 644 rpm.
(2) The shaft consists of a 3-in diameter aluminum segment that is rigidly joined to a 2-in diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the angle of twist developed at the interface of the two segments when the torque T = 50 kip in is applied. Use G = 4×106 psi for aluminum and G = 12×106 psi for steel. | Aluminum 3-in. diameter 6 ft T Steel 2-in. diameter 3 ft D
1. The hollow steel shaft (G=12 000000 Psi) must transmit a torque of 300000 lb-in. The total angle of twist must not exceed 3 degrees per 100 ft. the maximum shearing strength must not exceed 16000 Psi. (a) Find the inside diameter "d" if the outside diameter is equal to 12 inches. (b) Find the maximum torsional shear stress and (c) Find the maximum torsional shear strain.
2) Determine the maximum torque that can be applied to a hollow circular steel shaft of 100mm outside diameter and 70mm inside diameter without exceeding a shearing stress of 60MPa or a twist of 0.5 deg./m. Use G= 83GPA
What is the minimum diameter in mm of a solid steel shaft that will not twist through more than 3° in a 7-m length when subjected to a torque of 10 kNm? What maximum shearing stress is developed? G = 75 GPa
What is the max shear stress on a shaft under a torque of T = 54.167 lb-ft having a diameter of 0.75 inches? (answer in psi).
03: A shaft carrying three loaded pulleys with stepped diameters as shown. The modulus of rigidity for the shaft is (G-28GPA) and the shaft segments have the same lengths 48N.m (AB-BC-CD-30Cm). Determinc the following: GON.m 144N,m 1- Maximum shearing stress in the shaft CD. 2- The angle of twist of the pulley A relative to B.