A solid 1.125-in-diameter steel shaft is subjected to torques T3 = 305 lb-ft and Tp= 90 Ib-ft, acting in the directions shown. If theallowable shear stress in the shaft is 18 ksi, determine the maximum torque Tcthat can be applied to the shaft.TBTp(1)DIb-ftAnswer: Tc= i

Answered: Image /qna-images/answer/2814cd29-498a-4e95-9e37-b17e6cd67d50.jpg

Answered: A solid 1.125-in-diameter steel shaft…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7000 N 7000 N 1 m- 2 m -1 m- 60° A The cross-section of bar BC is rectangular with 40 mm width and 10 mm thickness. A 20 mm diameter bolt at A and a 15 mm diameter bolt at B are used to form a structure as shown above. Determine: • The normal stress in bar BC. • The shear stress in bolt A and bolt B.
3 - A torque of 2000 N-m is applied on a steel circular shaft with a diameter of 50 mm. The shaft has a length of 2 m. The Young's modulus and Poisson's ratio of the steel are E = 200 GPa and ✓= 0.3, respectively. What is the maximum shearing stress? What angle of twist occurs over the length of the shaft?
The center post B of the assembly has an original length of 124.7 mm, whereas posts A and C have a length of 125 mm. If the caps on the top and bottom can be considered rigid, determine the average normal stress in each post. The posts are made of aluminum and have a cross-sectional area of 400 mm Eal = 70 GPa. |800 kN/m +100 mm -100 mm A B 125 mm I800 kN/m Answer: 0A = 0c = 189 MPa, oB 21.4 MPа
2.0 in 3.0 in. The tubular torsional shaft shown above is made ofa stainless steel metal with the following properties: E = 28500 ksi • G= 11000 ksi • v = 0.37 If the pipe cross-section is subjected to an internal torque of T 50 kip-in, which of the following is closest to the minimum shear stress action on the cross-section? 3.92 ksi 1.57 ksi 7.84 ksi
The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tcircle/ Tsquare of the shear stresses. Given: r = 12 mm, S = 22 mm, and t = 2.09 mm.
a)jj holiow steel tube jsed in a roof structure has an outer diameter, d; = 104 mm and inner diameter, dz = 82 mm. The length of the tube is given by L = 2.75 m and has shear modulus, G = 28 GPa. If the tube is twisted in pure torsion by torques acting at the ends, distinguish the angle of twist when the maximum shear stress, Tmax = 48 MPa.
Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Determine the magnitude of the force P (in lb) for which the tensile stress in rod AB is thrice the magnitude of the compressive stress in rod BC if Q = 20.11 lb.
A solid circular bronze [G = 6,500 ksi] shaft, 6.0 ft long and 1.325 in. in diameter, carries a torque of 90 Ib-ft. For this shaft, determine: (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax = psi (b) Ф%3D
4. Two solid shafts of different materials are rigidly fastened together and attached to rigid supports as shown in the figure together with the given section properties. The torque of 1000 N-m is applied at the junction of the two segments. Compute the maximum shearing stress developed in the assembly. Answer: TĄ = 5.57 MPa Ts = 22.0 MPa 3 m 1.5 m Ta Aluminum Steel 75 mm dia. T=1.0 kN•m Ga- 28 GN/m²? 50 mm dia G, - 83 GN/m?
A 2 m long shaft is transmitting 90 kW at 150 RPM. The allowable shear stress in the material is 60 MPa. If the shaft is not allowed to twist more than 1°, then the diameter of the shaft required will be (Take G = 85 GPa)

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A solid 1.125-in-diameter steel shaft is subjected to torques Tg = 305 Ib-ft and Tp= 90 lb-ft, acting in the directions shown. If the allowable shear stress in the shaft is 18 ksi, determine the maximum torque Tcthat can be applied to the shaft.