A soil has a liquid limit of 61 and a plastic limit of 30. A moisture content test performed on an undisturbed sample of this soil yielded the following results: Mass of soil + can before placing in oven = 96.2 g %3D Mass of soil + can after removal from oven = 71.9 g Mass of can = 20.8 g 1. Compute the plasticity index 2. Compute the moisture content 3. Compute the liquidity index

A soil has a liquid limit of 61 and a plastic limit of 30. A moisture content test performed on an undisturbed sample of this soil yielded the following results: Mass of soil + can before placing in oven = 96.2 g %3D Mass of soil + can after removal from oven = 71.9 g Mass of can = 20.8 g 1. Compute the plasticity index 2. Compute the moisture content 3. Compute the liquidity index

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following results were obtained from a liquid limit test on a soil using a liquid limit device. The in-situ water content of this clay is 38% and the plastic limit is 20%. (Note: show the semi-log graph for the determination of the LL) Determine the following: (a) Liquid Limit of the soil, (b) Plasticity Index of the soil, and (c) Liquidity Index of the soil (d) shrinkage limit using the plasticity chart
A natural soil deposit is to be used for a geotechnical engineering project. Laboratory test results indicate that the soil possesses liquid and plastic limits of LL = 30% and PL = 22%, respectively. In addition, the sieve analysis has produced the following information: • % Passing Sieve No. 4 (4.75 mm) % Passing Sieve No. 200 (75 μm) • Coefficient of Uniformity C₁ 100% 8% 1.590 0.012 Coefficient of Curvature Co (a) Determine the soil's classification in accordance with the Unified Soil Classification System (USCS). (b) To further improve the soil's shear strength performance, the natural soil deposit (possessing an in- situ water content of w = 14%) was compacted in-situ and has achieved a saturation degree of S = 85%. If the specific gravity of soil solids is G, = 2.6, determine the soil's dry and bulk unit weights (ya and y) in its current compacted state.
Following are the results from the liquid and plastic limit tests for a soil. Liquid limit test: let the N1 be 15 and w1 be 28% let N2 be 21 and w2 be 23% let N3 be 33 and w3 be 14% For Plastic limit test: let w1 be 13 and let w2 be 15 and let w3 be 14 The liquid limit = Plastic limit = Plasticity Index =
i need the answer quickly
A liquid limit test on a clay was performed with the following results. The natural water content of the clay is 38% and plastic limit is 21%. Number of Blows 6 12 20 28 32 Water content (%) 52.5 47.1 42.3 38.6 37.5 What is the liquid limit of this clay? (Use Interpolation) Group of answer choices 39.85% 39.99% 36.74% 38.63% Please answer this asap for upvote. Thanks
The unit weight of the soil in the field was recorded as 126.360 lb/ft3 with natural water content of 16.020 %. In the laboratory, the soil is tested for its maximum and minimum void ratio which were 0.910 and 0.380, respectively, and the specific gravity of soil solids to be 2.780. Determine the following: in situ void ratio , relative density of the soil , percentage decrease in the void ratio if the relative density is increase by 10%
Following are the results of a shrinkage limit test. Determin the shrinkage limit, in percent, of the soil. Round off to two decimal places.
Problem Set 2: 4. A sample of gray silty clay has a mass of 126 kg. Laboratory tests results give a moist density (p) of 2.05 g/cm³, a specific gravity of solids (G,) of 2.71, and a moisture content (w) of 15.7%. First determine all entries in the phase diagram. Then determine the void ratio (e), the porosity (n), the degree of saturation (S), the dry density (Pa), the dry unit weight (ya), and the moist unit weight (y). Draw the Phase diagram.
In a standard proctor test, 3.2 kg of moist soil was filling the mould of volume 944 cc after compaction. A soil sample weighing 40 gm was taken from the mould and oven dried for 24 hours at a temperature of 110°C. Weight of dry sample was found to be 34 gm. Specific gravity of soil solids is 2.5. The theoretical maximum value of the dry unit weight of soil at that water content is equal to
05: The Figure below represents the data that was obtained from a liquid-limit test on a soil. 50 percent of its particles is passing sieve #200. Two determinations for the plastic limit gave water contents of 20.3 % and 20.8 %. Determine 1- Liquid Limit (LL). 2- Plasticity index. 3- Liquidity index if the water content is 27.4% 4- Void ratio at the liquid limit, if G, 2.7 5- Classify the soil based on AASHTO system. 30 10 20 40 60 80 100 Penetration, d (mm) Moisture content, w ()
A soil is mixed at a water content of 16% and compacted in a 1000 ml cylindrical mold. The sample extruded from the mold has a mass of 1620 g, and the specific gravity of the soil grains is 2.69. Find the following: a. void ratio, b. degree of saturation, and c. dry unit weight of the compacted sample. d. If the sample is soaked in water at the same void ratio, what would be the new water content?
Discuss your results and compare your results with any published data. For the bulk density test, obtain the value of dry density. How does the values of (i) void ratio (ii) porosity influenced your results? How will these values differ if the soil is fully saturated, partially saturated or submerged? Support your assertions using relevant phase relationship equations. Whatwill happen to the values of particle density (specific gravity) obtained if the soil sample contain large quantities of peat or organic material? How will the results be used in specific practical conditions in the construction industry? Explain any source(s) of error in your experiment and state how it affected your result.