A smooth two dimensional flat plate is exposed to a wind velocity of 100 km per hour. If laminar boundary layer exists upto a value of Reynolds number equal to 3 x 105, then the maximum thickness of laminar boundary layer will be [Take kinematic viscosity of air as 1.49 x 10-5 m2/s] mm.

A smooth two dimensional flat plate is exposed to a wind velocity of 100 km per hour. If laminar boundary layer exists upto a value of Reynolds number equal to 3 x 105, then the maximum thickness of laminar boundary layer will be [Take kinematic viscosity of air as 1.49 x 10-5 m2/s] mm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A wheel applies a 40-kN load on a semi-infinite elastic space, as shown in Fig. P2.1. The modulus of…

Q: True or False: The rate of adsorption increases with increasing temperature. Please explain in…

A: The phenomenon of attracting and retaining the molecules of gases or liquids on a solid surface is…

Q: for part b, what happened to the t on the cty when integrating, can you please show this work again?

A: Given: u = A(1+bt) , v = cty Required: To explain the stream line equation done in step 2 by the…

Q: scosity 1.5 Pa-s flows at a velocity of 10 m/s in a 0 cm dia pipe. What will be the boundary shear…

A: Density(p)= 1260kg/m³ absolute viscosity(u) =1.5 pa-s Velocity (V) = 10m/s Diameter (d) = 10cm = 0.1…

Q: Q2). A 20m steel tape supported at both ends was used to measure horizontal distance of CD at a…

Q: What are the major thermal factors to consider when selecting a material?

A: The significant thermal variables to consider while choosing a material are Thermal conductivity…

Q: material has a grain diameter of 0.0005 cm. What height of capillary rise will you expect? The…

A: Radius=diameter/2 r=0.000005/2 r=2.5*10-6 m

Q: 30kg and ma= 70 kg. Between all of the contacting swrfaces, u, = 0.1. What is the largest force F…

Concept explainers

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.

Question

A smooth two dimensional flat plate is exposed to a wind velocity of 100 km per
hour. If laminar boundary layer exists upto a value of Reynolds number equal to 3 x
105, then
the maximum thickness of laminar boundary layer will be
[Take kinematic viscosity of air as 1.49 x 10-5 m2/s]
mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: solution

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A circular nylon [E = 8 GPa; ν = 0.35; α = 29 ×10-6/°C] disk with a circular hole in its center is shown. At an initial temperature of Ti = 22°C, the outer diameter of the disk is D = 210 mm, the diameter of the central hole is d = 55 mm, and the thickness of the disk is t = 24 mm. At a final temperature of Tf = 46°C, determine:(a) the change in diameter Δd of the central hole (assume an increase Δd as positive, otherwise as negative).(b) the change in thickness Δt of the disk (assume an increase Δt as positive, otherwise as negative).(c) the normal strain in the circumferential direction around the outside of the disk.
A line was determined to be 2538.45 m when measured with a 45m tape supported throughout its length under a pull of 3.4 kg at a mean temperature of 36⁰C. Tape used is of standard length at 20.2⁰C under pull of 4.1 kg. Cross sectional area of tape is 0.03 cm^2. Coefficient of thermal expansion is 0.0000116/⁰C. Modulus of elasticity of tape is 2.3x10^6kg/cm2 ▪ Determine the error of tape due to change in temperature. ▪ Determine due the error of tension. ▪ Determine the corrected length of the line.
A line was measured to be 2682.35m using a 30m steel tape supported throughout its length under a pull of 4.4kg. The mean temperature during measurement is 34 degree Celsius. The tape used has a cross sectional area of 0.03 square centimeters and has a standard length of 20degree Celsius under a pull of 5.5kg. The modulus of elasticity of the tape material is 2 x 10^6 kg/cm^2 and the coefficient of thermal expansion is 0.0000116 per degree Celsius. a. Determine the error due to temperature change. b. Determine the error due to tension. c. Determine the corrected length of the line.
Explain about the vertical and horizontal coefficients of permeability.
Q.2) Calculate the moment of inertia (Ix, and ly,) about the given axis for the composite area shown in figure. Ye la 165 m 0.8 m 0.1m 0.265 m 1m 0.5m
Steel railroad rails 10 m long are laid with end-to-end clearance of 3 mm at a temperature of 15°C. (a) At what temperature will the rails just come in contact? (b) What stress would be induced in the rails at that temperature if there were no initial clearance? Use a = 11.7 x 106 /°C and E = 200 GPa.
Please don't copy the wrong answer
Axial Forces Column Krowns Circular Cross sectional area Axial Compression: Elastic Modulus top half: Elastic Modulus bottom half 5 m 5 m 600 kN 20.000 mm² 600 kN 12,000 MPa 10.000 MPa 1) What is the Axial Stress at any point in the top half of column? 2) What is the Axial strain at some point in the top half column? 3) What is the Axial Stress at any point in the bottom half of column? 4) What is the Axial strain at some point in the bottom half of column? 5) Calculate the axial deformation of the column from the Compression Force
When a bar of certain material 40mm square is subjected to an axial pull of 1,60,000N the extension on a gauge length of 200mm is 0.1mm and the decrease in each side of the square is 0.005mm. Calculate Young's modulus, Poisson's ratio. Shear modulus and bulk modulus for this material.