A slice of intrinsic silicon bar is 3 mm long and has a rectangular cross-section 50 µm x 10 µm. At 300 K, determine the electric field intensity in the bar and the voltage across the bar when a steady current of 2 µA is measured. Take the value of resistivity p = 2.30 × 105 Ncm at room temperature (300 K).

A slice of intrinsic silicon bar is 3 mm long and has a rectangular cross-section 50 µm x 10 µm. At 300 K, determine the electric field intensity in the bar and the voltage across the bar when a steady current of 2 µA is measured. Take the value of resistivity p = 2.30 × 105 Ncm at room temperature (300 K).

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Germanium doped with 104 m* Al atoms is a semi-conductor at room temperature and each Al atom creates a charge carrier. Is the material obtained a p-type or an n-type semiconductor?
7. A diode conducts 1mA at 20°C. If it is operated at 100°C, what will be the current? Given data: n=1.74 and NTC value = 2.2mV/°C.
Determine the value of voltage across R1 and value of R2 in the given circuit if a current of 2.2 mA is flowing through the diode when a forward bias voltage of E=5 V is applied and R1=690 Ohms. Assume diode as silicon. R1 D2 TE R2 Voltage across R1 Resistance of resistor R2
You work as an engineer in a company and you have been given the assignment of measuring the electrical conductivity and the band gap (Eg) of a new intrinsic semiconductor material at 20 and 100 °C. You cut this material in the form of a rectangular prism with a length of 30 cm, a width of 1 cm and a thickness of 2 cm, and you applied a potential difference of 1 V by placing electrodes on the faces shown in the figure. In this case, you measure a current of 0.8A at 20 °C and 12A at 100 °C. According to this information b) the band gap of this material. 30 ст 2 cm 1 ст
From the diode circuit shown in Figure 1, show how to determine the resulting output voltage signal. Given the input voltage signal Vi it is as shown in Figure 1 on the left and the diode used in Circuit 1 is 1.1. Ideal diode 1.2. Diode using approximation model 10 ARA " t V₁ O 1kQ www 1k2 Figure 1 SI Z ww ΣΚΩ V₂ +15V
Current 420 ohm 30 V 1,(max) = 80 mA Voltage Vp-in 2.2 kohm Vp-out 0.6 V Zener Current Answer the following question according to the above. Remember Kirchhoff's laws when making your calculations in this question. According to the given graph, how many volts is the voltage value on it when this Zener diode is on a flat supply?
What will be the value of thermal voltage for semiconductors? Estimate its value at 400 K.
Electrical Engineering please solve this thank you The following values are given for a shocdley diode Vi (derel vollaye) • 0.025 V Is (Deverse salunalia cmal): 10X10A -15 Given voltaye eg ^: v(t) = 0.7+ 8 Vr cosut IA RL= 50 0 %3D Find avg. powen diipted in shochly diode € ay.power deliveud to load
When a Ge diode is conducting at a temperature of 25oC, VT = 0.68 V. What is the VT at 106oC?
QUESTION 1 In the figure V-47 volts, and R=117 ohms. Determine the current (in unit of mA) in the diode, assuming the practical model V SIZ R (Write the answer by using 0 decimal places after the point)
Using 2nd approximation for the circuit shown, assuming that the diode used is a silicon diode, determine the currents ID1, ID2 and current through R2. Finalize answers as follows: ID1= Ir2= ID2= R2 D1 3.3 kQ BAT1 D2 20 V R1 5.6 kn
Q1: ideal diodes are used in the circuit shown in figure. Sketch the output voltage 1Kohm D3 V=10Sinwt D2 Vo E1=7V E2=5V+