A ski jumper starts with a horizontal take-off velocity of V; = 20 m/s and lands on a straight landing hill inclined at e = 35°. Determine (a) the time between take- off and landing (b) the length d of the jump. %3D

A ski jumper starts with a horizontal take-off velocity of V; = 20 m/s and lands on a straight landing hill inclined at e = 35°. Determine (a) the time between take- off and landing (b) the length d of the jump. %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The force Pis applied to the 42-kg block when it is at rest. Determine the magnitude and direction of the friction force exerted by the surface on the block if (a) P = 0, (b) P = 151 N, and (c)P = 226 N. (d) What value of Pis required to initiate motion up the incline? The static and kinetic coefficients of friction between the block and the incline areu, = 0.22 and Hk = 0.19, respectively. The friction force is positive if up the incline, negative if down the incline. 42 kg H, = 0.22 H = 0.19 13 Answers: (a) F= i (b) F= i N (c) F= i N (d) P= i N
The elevations of the ski jumping hill are as follows: hA = 44 mhB = 1.6 mhC = 4.9 m If the velocity of a ski jumper is measured to be 27.9 m/s at position B, what will be the launch velocity (in m/s) at position C.
Bucket A and block C are connected by a cable that passes over drum 8. Knowing that drum B rotates slowly counterclockwise and that the coefficients of friction at all surfaces are -0.35, determine the smallest combined mass m of the bucket and its contents for which block C will start moving up the incline Given that 0 = 35° and W = 90 kg %3D Answer in 3 ecimals and
A two-tier system to repair bridges is supported by two steel cables for each platform. Lengths of the cables are la = 50 in. and lp = 190 in. Assume that two 190 lb workers are going to be standing on the system to repair a bridge, one on each platform. The following design requirement must be met: the stretch of each cable must be less than 0.02 in. at the worst-case loading condition for each cable. 140 in. 250 lb 190 in. 400 lb Determine the minimum diameter required for each cable. (Express your answers using two decimal places.) Cable at A: in. Cable at B: in. Cable at C: in. Cable at D: in.
A 450-N is in contact with a level plane of fk = 0.10. The block is acted upon by a horizontal force of 75N. The block reaches a velocity of 15m/s, starting from rest. If the 75-N force is then removed, how much longer will the block continue to move?
Answer fast
Disk A rolls without slipping along the ground with an angular velocity of w = 5 rad/s as shown in the diagram. Determine the velocity of Collar C at this instant if it is confined to move along 60° inclined slot. Use the Instantaneous Center (IC) method only. Include the free body diagram and step by step solution with detailed explanations. A 2 ft B 45° 4.123 ft 30° с w = 5 rad/s 60°
strength of materials
The box slides down the slope described by the equation y = (0.05x²) m, where x is in meters. If v, = -3 m/s, and a, = -1.5 m/s? at x = 5m, find the y-components of the velocity and the acceleration of the box at x = 5m. 0.15 m/s , 1.5 m/s^2 1.5 m/s , 0.15 m/s^2 5.01 m/s, 1.05 m/s*2 0.51 m/s, 5.1 m/s^2
The force P is applied to the 63-kg block when it is at rest. Determine the magnitude and direction of the friction force exerted by the surface on the block if (a) P = 0, (b) P = 187 N, and (c) P = 314 N. (d) What value of P is required to initiate motion up the incline? The static and kinetic coefficients of friction between the block and the incline are u = 0.21 and uy = 0.15, respectively. The friction force is positive if up the incline, negative if down the incline. 63 kg 19 4, = 0.21 HE = 0.15 13 Answers: (a) F= i N (b) F = i N (c) F = i N (d) P= i
Determine the magnitude of F1 and the distance y if x = 1.5 m and F2 = 1000 N.
100 lb In the fig. shown, compute the minimum Weight W to prevent impending motion of the block up the incline. The weight of the block is 100 lb as shown and the coefficient of friction between the block and the incline u = 0.45. Assume frictionless pulley. 450