A single strain gauge is bonded to a beam 0.1 m long and has a cross section area 4 cm². Young modulus for steel is 207 GN/m². The strain gauge unstrained resistance of 250 2 and a gauge factor of 2 when a load is applied the resistance of gauge change by 0.013 2. Calculate the change in length of the steel beam and the amount of force applied to the beam.

A single strain gauge is bonded to a beam 0.1 m long and has a cross section area 4 cm². Young modulus for steel is 207 GN/m². The strain gauge unstrained resistance of 250 2 and a gauge factor of 2 when a load is applied the resistance of gauge change by 0.013 2. Calculate the change in length of the steel beam and the amount of force applied to the beam.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

A certain laminated core has a permeability of 2,500. The length is 5.5 cm and the cross section is 2.1 sq. cm. What is its reluctance? Draw the diagram for the question
The principle operation of LVDT is based on the variation of Select one a. Self inductance b. Reluctance c. Mutual inductance d. Permanence
How temperature effect conductivity? Explain with the help of following equation. m e'n7'
1. What is the reluctance of 10 cm diameter silicon steel of 2500 permeability with a mean length of 20 cm? A. 0.000201 cgs B. 0.000102 cgs C. 0.000212 cgs D. 0.000123 cgs 2. At what rate the flux must be varied to measure 12 V across the terminal of 300 turns coil? A. 0.05 Wb/s B. 0.04 Wb/s C. 0.03 Wb/s D 0.02 Wb/s
A resistance strain gauge with a gauge factor of 2.0 is fastened to a steel member subjected to a stress of 100 N/mm². The modulus of elasticity of steel is approximately 2×105 N/mm². The percentage change in resistance is?
The resistance of wire increases from 40 – ohm at 20 0C to 50 – ohm at 70 0C. Find the temperature coefficient of resistance at 0 0C.
For the given circuit be ow, is there current flowing on the circuit? (Answer with Yes or No only)
A certain laminated core has a permeability of 3,150. The length is 4.85 cm and the cross section is 2.32 sq. cm. What is its reluctance?
Q1: A plare (100 mm) wide and (15 mm) thick is joined with another plate by a single transverne weld and a doubie parailei fillet weld as shown in figure The maximum tensile and shaar stresses are (75 Mga & 60 Mpa) raspectively Find the lengh of each panallel fillet weld. ifthe jeint is subjected to static loading
Look for Requivalent(Equivalent Resistance).Please show details
question 22 What is the relative permeability of a ferromagnetic material whose absolute permeability is 750 * 10-6 Wb/At*m? (vacuum permeability is 4p 10 Wb/At*m) O 9.42 10 -10 O 597 O 16.75 O 0.1675
multirange ammeter was designed using direct method to give three scales with Rsh1= 0.001285989 0, Rsh2=0.000562552 0, and Rsh3=0.000100001 Q. The d'Arsonval meter has Rm=6 Q and full scale current of 1.5 mA. Find the ranges.? 8 (Ctrl) -