A single-stage impulse turbine of nozzle efficiency, 90%, nozzle angle=20, absolute velocity of steam entering moving blade-672.4m/s, the ratio of blade speed to whirl component of steam speed 0.5, blade velocity coefficient =0.9.the velocity of steam entering the nozzle =20mis. Determine the blade angles at inlet and outlet if the steam enters into the blades without shock and leaves the blades in an axial direction, 2- blade efficiency, and 3- power developed and axial thrust if the steam flow is 8kg/s (Solve using the velocity diagram).

Q: Energy balance results (in kW) obtained for the same medium speed single cylinder diesel engine are…

A: Since, In the case 1 it is given that water has extracted 7.1 kW of heat from the cylinder so there…

Q: A Pelton wheel operates with an effective head of 310 m producing 15 MW of power. The overall…

A: The number of jets generally speaking you don't what they're to be than 30 jets for every message…

Q: D1/ The folle and a fixed r blade speed angle of the fa factor for all Using a suitat (i) Developed…

A: INTRODUCTION : Steam turbines are the prime movers in which the heat energy of the steam is…

Q: A single-stage, single-acting air compressor with runs at 700 r/min. It has a polytropic index of…

A:

Q: Air Is To Be Compressed In A Single-Stage Reciprocating Compressor From 1.013 bar And 15°C To 7…

A:

Q: An axial flow Impulse gas turbine stage receives a mass flow rate of 75 lbm/s at a velocity V1. It…

A:

Q: ramjet engine is to be designed for a maximum thrust of 1000 lb at sea level at a velocity of 950…

A:

Q: Work out put =0.6 Parameters Inlet Temperature Pressure Velocity Outlet X = 0.85 50 kPa 50 m/s 350…

A:

Q: For a centrifugal compressor designed to have a stagnation pressure ratio of 3.95, determine an…

A:

Q: A single-stage impulse turbine with a diameter of 120 cm runs at 3000 rpm. If the blade speed ratio…

A: Given:Diameter of impeller, d=120 cm or 1.20 mSpeed, N=3000 rpmBlade speed ratio, uV=0.42

Q: Steam with velocity of 900 m/s exits the nozzle of a 2-stage Curtis turbine with equiangula stator…

A:

Q: Describe the functions of nozzles in turbines.

A: Nozzle It is a device used to obtain the kinetic energy of the fluid. It is spherical or cylindrical…

Q: To maximise power in Pelton turbine, the bucket speed must be (1) equal to the jet speed (2) equal…

A: Given:Pelton wheel impulse turbine,Find,At what condition the power of turbine is maximum?

Q: Problem 5: Calculate the thrust of a gas turbine engine if the exhausting jet expands to ambie…

A:

Q: A trial run on a steam turbine power plant gave the following results Entrance to boiler Exit of…

A: Given DataVi=5m/sHin=850kJ/kgZi=4.3mVo=25m/sHo=2625kJ/kgZo=0m˙=3600kg/hr=1kg/sQ˙=2100kJ/sec

Q: maximum blade efficiency (in percent) is

A: Given,  Velocity of steam,V=10 m/sBlade angle,θ=300Enthalpy drop in the stage= 100 kJNozzle…

Q: A Peloton turbine is driven by two jets generating 4.0MW at 375 rpm. The head at the nozzles is 200…

A:

Q: 07. An inward flow radial turbine involves a nozzle angle, a, of 60° and an inlet rotor tip speed,…

A:

Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…

A:

Q: The steam from the nozzles of a single wheel impulse turbine is 600m/s and at 20degree to the plane…

A: Given  Inlet velocity = 600 m/s Angle = 20o N = 3000 rpm Blade radius = 590 mm Exit velocity = 164…

Q: A centrifugal compressor with backward bent blades (B = 75°) handles 20 kg/s of air, where the air…

A:

Q: lbert bought a portable device to pump his truck tyres. On the manual, he found out that the device…

A:

Q: 3. Describe the different parts of radial flow reaction turbine.

A: Describe different parts of reaction turbine

Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…

A:

Q: the available power from the physical environment. 2 the flow rate 3 the inlet angle of the rotor…

A:

Q: Consider an engine with a maximum speed of 7000 rpm. The bore and stroke are 0.1 m, each. For an…

A: Solution is given below.

Q: Albert bought a portable device to pump his truck tyres. On the manual, he found out that the device…

A:

Q: Q.3. Choose "True" or "False" for the following: 1. In an outward flow reaction turbine, water…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.