A single phase transmission line is delivering 470 kVA load at 14 kV. Its resistance is 4 Ω and inductive reactance is 8 Ω. If the load power factor is 0.9 lagging. Determine the 1Current through the line: 2Sending end voltage: 3Sending end power factor: 4Regulation of transmission line: 5Efficiency of transmission line

A single phase transmission line is delivering 470 kVA load at 14 kV. Its resistance is 4 Ω and inductive reactance is 8 Ω. If the load power factor is 0.9 lagging. Determine the 1Current through the line: 2Sending end voltage: 3Sending end power factor: 4Regulation of transmission line: 5Efficiency of transmission line

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
A single phase transmission line is delivering 410 kVA load at 10 kV. Its resistance is 5.5 ohm and inductive reactance is 8 ohm if the load power factor is 0.7 lagging. Determine the Current through the line Sending end voltage Sending end power factor Regulation of transmission line Efficiency of transmission line
For transferring electrical power at 220 kV, six conductors of ACSR Drake constitute a 60Hz double circuit three phase line arranged as shown below. The vertical spacing between consecutive conductors is 14ft; the longer horizontal distance is 32ft whereas the shorter horizontal distance is 25ft. a. Find the inductance per phase per mile and the inductive reactance per phase in ohms per mile. b. Find the capacitive reactance to neutral in ohm-miles. c. Find the resistance per phase per mile in ohms per miles. d. If the length of the line is 90 miles then draw an equivalent circuit of the line and analyse the open circuit and short circuit performance of the line. e. Find the maximum power we can transmit over the line. f. If the line is delivering power to a load of 20MW at 0.8 power factor lagging then find the voltage at the receiving end of the line. Also, Determine the voltage regulation, losses and efficiency of the line. g. If a fixed shunt compensation of 3 MVAr is attached at…
Hey i have less time i want this solution please help me
In the following network, the voltage magnitudes at all buses are equal to 1 p.u., the voltage phase angles are very small, and the line resistances are negligible. All the line reactances are equal to j1 p.u. (1) (2. P₂ = 0.1 p.u. P3 = 0.2 p.u. The voltage phase angle 83 in radian at bus 3 is (Assume one of the generator bus as slack bus and sin-¹ (0.1) = 0.1 rad) (a) -0.1 (b) -0.2 (c) 0.1 (d) 0
Power System: Please Show All Works
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
A three-phase 20 kV medium-voltage line is 10 km. Resistance is 0.365 2/km and reactance is 0.363 2/km (inductive). Voltage at the beginning of line is 20.5 kV. At the end of the line is loading P= 800 kW with power factor 0.95ind. Draw 1-phase equivalent diagram and calculate load current, line voltage at the end the of line, voltage drop and power losses of the line.
A 5 km long, 3-phase 34.5 kV line has a horizontal configuration of 4 ft. spacing. The conductor is 336.4 ACSR with GMR of 0.0244. What is the inductance of the line? * A. 7.63 mH B. 4.76 mH C. 5.33 mH D. 6.49 mH
Answer the first and last 2 qestion Step By Step
Q2: The constants of a 275 KV transmission line are A = 0.8525° and B = 200275° 0/phase. Draw the circle diagram to determine the power and power angle at unity power factor that can be received if the voltage profile at each end is to be maintained at 275 KV. What type a rating of compensating equipment will be required if the load is 150 MW at unity power factor with same voltage profile. (5.5 mark)
A three-phase 20 kV medium-voltage line is 10 km. Resistance is 0.252 2/km and reactance is 0.128 92/km (inductive). Voltage at the beginning of line is 21.0 kV. At the end of the line is loading P = 2.5 MW with power factor 0.92ind. Draw 1-phase equivalent diagram and calculate line voltage at the end the of line, active and reactive power at the beginning of the line and power losses of the line.