A single- phase overhead transmission line delivers power of 1 MVA at 11kV at 0.86 power factor laggin The total resistance of the line is 12 ohm and its total inductance is 90 mH. Determine a) sending-end voltage b) sending-end power factor c) percentage voltage regulation d) transmission efficiency

A single- phase overhead transmission line delivers power of 1 MVA at 11kV at 0.86 power factor laggin The total resistance of the line is 12 ohm and its total inductance is 90 mH. Determine a) sending-end voltage b) sending-end power factor c) percentage voltage regulation d) transmission efficiency

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Related questions

Q: The figure below shows the one-line diagram of a three-phase power system. By selecting a common…

A: In this question we need to draw a per unit impedance diagram of the given system.

Q: A 100 km long three phase transmission line has resistance 12Ω per phase, inductance per phase 0.15…

Q: 44020⁰ 4402120° n a 440Z-120° Ib 6-j8 Ω 6-j8Q2 N (6-j8 Ω Ic 1. Calculate the line currents for…

A: In this question, we need to determine the line currents, line to neutral voltage and various…

Concept explainers

Short Transmission Line

A short transmission line is a transmission line that has a length less than 80 kilometers, an operating voltage level of less than 20 kV, and zero capacitance effect.

Power Flow Analysis

Power flow analysis is a topic in power engineering. It is the flow of electric power in a system. The power flow analysis is preliminary used for the various components of Alternating Current (AC) power, such as the voltage, current, real power, reactive power, and voltage angles under given load conditions and is often known as a load flow study or load flow analysis.

Complex Form

A power system is defined as the connection or network of the various components that convert the non-electrical energy into the electric form and supply the electric form of energy from the source to the load. The power system is an important parameter in power engineering and the electrical engineering profession. The powers in the power system are primarily categorized into two types- active power and reactive power.

Question

A single- phase overhead transmission line delivers power of 1 MVA at 11kV at 0.86 power factor lagging.
The total resistance of the line is 12 ohm and its total inductance is 90 mH. Determine
a) sending-end voltage
b) sending-end power factor
c) percentage voltage regulation
d) transmission efficiency

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Consider the single-Line diagram of a power system shown in Figure 3.42 with equipment ratings given: Generator G1: 50MVA,13.2kV,x=0.15p.u. Generator G2: 20MVA,13.8kV,x=0.15p.u. Three-phase -Y transformer T1: 80MVA,13.2/165YkV,X=0.1p.u. Three-phase Y- transformer T2: 40MVA,165Y/13.8kV,X=0.1p.u. Load: 40MVA,0.8PFlagging,operatingat150kV Choose a base of 100 MVA for the system and 132-kV base in the transmission-line circuit. Let the load be modeled as a parallel combination of resistance and inductance. Neglect transformer phase shifts. Draw a per-phase equivalent circuit of the system showing all impedances in per unit.
Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
In the following network, the voltage magnitudes at all buses are equal to 1 p.u., the voltage phase angles are very small, and the line resistances are negligible. All the line reactances are equal to j1 p.u. (1) (2. P₂ = 0.1 p.u. P3 = 0.2 p.u. The voltage phase angle 83 in radian at bus 3 is (Assume one of the generator bus as slack bus and sin-¹ (0.1) = 0.1 rad) (a) -0.1 (b) -0.2 (c) 0.1 (d) 0
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
For transferring electrical power at 220 kV, six conductors of ACSR Drake constitute a 60Hz double circuit three phase line arranged as shown below. The vertical spacing between consecutive conductors is 14ft; the longer horizontal distance is 32ft whereas the shorter horizontal distance is 25ft. a. Find the inductance per phase per mile and the inductive reactance per phase in ohms per mile. b. Find the capacitive reactance to neutral in ohm-miles. c. Find the resistance per phase per mile in ohms per miles. d. If the length of the line is 90 miles then draw an equivalent circuit of the line and analyse the open circuit and short circuit performance of the line. e. Find the maximum power we can transmit over the line. f. If the line is delivering power to a load of 20MW at 0.8 power factor lagging then find the voltage at the receiving end of the line. Also, Determine the voltage regulation, losses and efficiency of the line. g. If a fixed shunt compensation of 3 MVAr is attached at…
2. The one-line diagram of a three-phase power system is as shown in the figure below. Impedances are marked in per unit on a 100-MVA, 400-kV base. The load at bus 2 is S2 = 15.93 MW-j33.4 Mvar, and at bus 3 is S3 = 77 MW +j14 Mvar. It is required to hold the voltage at bus 3 at 4006 0 kV. Working in per unit, determine the voltage at buses 2 and 1. V3 j0.5 pu V₂ S₂ j0.4 pu S3
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
High voltage engineering subject
A short single phase transmission line has a loop impedance of (0.2+j1.2) ohm. At what leading power factor the voltage regulation will be zero ?
A single phase transmission line delivers 1500 kW at 33 kV at 0.8 p.f. lagging. The total resistance and inductive reactance of the line are 10 2 and 15 2 respectively. Determine (i) sending end voltage (ii) sending end p.f. and (iii) efficiency of transmission.
A single phase line has an impedance of 0.4+j2.7 ohms. The line feeds two -single phase loads that are connected in parallel. The first load is absorbing 264.1 kVA at 0.707 power factor lagging. The second load absorbs 44kW at unity power factor. The voltage at the load end of the line is 2200 V. Assuming at the load end of the line as the reference axis. Determine the magnitude of the voltage at the source end of the line.
A surge of 100 kV travels along an overhead line towards its junction with a cable. The surge impedance for the overhead line and cable are 400 ohms and 50 ohms respectively. The magnitude of the surge transmitted through the cable is ?