A single phase energy meter which is designed to make 120 revolution for one unit of energy. It takes N number of revolution when connected a load which carrying a current of 35A at 220 V and 0.55 power factor for one hour. If the energy meter actually makes 490 revolution, then what would be the percentage error, does the meter is moving fast or slow.

A single phase energy meter which is designed to make 120 revolution for one unit of energy. It takes N number of revolution when connected a load which carrying a current of 35A at 220 V and 0.55 power factor for one hour. If the energy meter actually makes 490 revolution, then what would be the percentage error, does the meter is moving fast or slow.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explain please why in electrodynamometer type wattmeter we use the fixed coil of the instrument which is wound with thick multistranded wire for measuring current and the moving coil is wound with thin and light wire for measuring voltage I have a doubt please
Calculate the peak voltage across R2 in the diagram R1 = 1 kohm, R2 = 680 ohms, supply voltage is 10V RMS 5.73V peak 10V peak 4.04V peak 1.75V peak
The energy meter constant is given by (a) revolutions - Wh (b) revolutions – kWh (c) revolutions / Wh (d) revolutions /kWh
The maximum value of an alternating voltage is 300 V. It takes 20 ms for one cycle. So write the formula for alternating voltage and (1) Find the time taken to reach 200 V for the first time after zero, and (2) find the value of the voltage at 18 ms.
In the figure R₁-3.41R, the ammeter resistance is zero, and the battery is ideal. What multiple of e/R gives the current in the ammeter? EH Number Units *E/R
What is the resistance to the changing flow of alternating current? Select one: A. AMPERES B. INDUCTANCE C. REACTANCE
How much change in the energy of wind will take place if wind velocity becomes 3 times
We want to measure the amount of current flowing to an old light bulb. We expect that the result will be around 5A. How should we connect the probes of the multimeter? Drag the connector images to the correct locations and "Not Connected" images to the rest. SUDE SWITCH: LEFT- OFF MIDDLE- DCVOLTS DC mA NUMERICAL VALUE OF VOLTS OR mA OR OHMS DISPLAYED HERE 0.00 OHMS RIGHT - AC VOLTS AC mA OFFOD AC DC-A DM 8010 MOVE ROTARY SWITCH TO THIS AREA TO READ OHMS 1000 200 20 MOVE ROTARY SWITCH TO THIS AREA TO READ VOLTS (SELECT RANGE) 200 (SELECT RANGE) 2K. 20K. •200 20u MOVE ROTARY SWITCH TO THIS AREA TOo READ mA (SELECT RANGE) 200K 20u *200u m 2M 20M 200m 20m 10A COM vn PROBES Windows'u Etkinleştir Windows'u etkinleştirmek için Ayarlar'a gidin. NOT CONNECTED
How long it would take for a current of v= ( 100sin314t+45°) amperes to complete one-fourth cycle?
A moving iron voltmeter reads 250v when connected to 250v dc .if connected to 250v 50 Hz .the voltmeter reading is likely to be 248 252 O 250 210
Draw a graph of current against time for two complete cycles of alternating current of peak value2 A and frequency 10 Hz. Label the axes and indicate correct scale of values on them.(Hin: youhave to calculate the time for one cycle in order to mark the x-axis)
When a load of 750 W is connected, the disc of a single-phase energy meter rotates at 16 revolutions per minute. If the load is on for 6 hours, determine the % error of the meter. The meter constant is 1200 revolutions/kWh in percentage?