A simply supported wood beam AB with span length L = 4 m carries a trapezoidal distributed load (see Figure 1). Calculate the maximum bending stress due to the load if the beam has a rectangular cross section with width b = 140 mm and height h = 240 mm. 5.8 kN/m 2.9 kN/m A B Figure 1 4 m

Q: How many "varas" are there in a single ruler measurement?

A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…

Q: Explain the principle of 5S in Construction. Complete the answer please.

A: Introduction- Construction- It refers to the methods and business associated with assembling and…

Q: Define Weight-Volume Relationships

A: The weight volume relationship is depicted in following properties:- Void ratio:- The ratio of…

Q: 32. What is the area of an octagon inscribed in a circle having an area of 224 sq.m?

A:

Q: Define Peclet number.

A: It is defined as the ratio of the rate of advection of a physical quantity by the flow to the rate…

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: What is the most common scale used for temperature

A: The Celsius and fahrenheit scale is used most commonly used.. Kelvin scale is primarily used in…

Q: What is a box model? Give the equation to represent box model.

A: The Urban air quality models has been called box models. The Figure is a schematic graph of a box…

Q: The solution came out all in one line. Making it difficult to understand. Please Can it be written…

A:

Q: Convert 24 inches to feet.

A:

Q: Draw the three projections showing the measurements, thanks for the cooperation

A:

Q: Identify the length of line A, B, and C. Create/Draw top view, left view, front view, and bottom…

A: Answer  Length of line A = 9.0-4  Length of line A = 5 Length of line B = 13.5-11.52 Length of line…

Q: Solve for the reactions and draw the shear and moment diagram. 9.35KN/m 2.00 5.00 116KN 9.35KN/m…

A:

Q: express each measurement in feet.42 inches

A: Given: The measurement is 42 in.

Q: what is the difference between 42 square meter and 42 meter square

A: It is needed to differenciate between 42 square meter and 42 meter square.

Q: How are units converted using dimensional analysis?

A:

Q: Convert 6.2 feet to inches.

A: Given: The measurement is 6.2 ft.

Q: Write the types of structures in detail.

A: The type of structure to be constructed for a purpose depends upon the use of structure, load on…

Q: If the actual dimension is 46 m and the scaled dimension is 184 cm, what is the scale used?

A:

Q: 57.5 inches tall. The scale of the model is 1 inch :9 feet.

A: Given Data : 57.5 inches tall measurement        Scale as 1inch:9feet To Determine: 57.5 inches…

Q: A drone is flying in the air at some altitude. The drone is equipped with piezometer that indicates…

A:

Q: Enumerate at least five different units of measurement that usually use at hom

A: There are many ways in which technology can help in this case. If you want to wake up early in the…

Q: ooking at the X direction, provide the front view, top view, and left-side view using the meter…

A: The isometric Front, and side. Top view of above drawing is given below:

Q: Solve for the reactions and draw the shear and moment diagram. 9.35KN/m 2.00 5.00 116KN 9.35KN/m…

A:

Q: H MM 0 10 20 30 40 50 60 70 80 90 100 DIMENSION THE PART USING METRIC DIMENSIONS. USE DIVIDERS OR…

A: The front view and top view of an object is shown in the above figures. Also scale of dimensions…

Q: How is the dimension paper used to compile an accurate Bill of Quantities??

A: Dimension paper is used in taking off which refers to the process which identifies elements of…

Q: What are the metric and/or SI units typically used in a Factor of Safety Calculation?

A: In the field of engineering, the factor of safety (FoS) is a dimensionless parameter used to…

Q: Task 8 - HIGH RISE BUILDINGS Steps on how to build a high rise buildings. (From rawland) Send a copy…

A: A low-rise structure's construction entails developing a framework that can sustain both its very…

Q: What is area of plot in rectangle shape. Length =20feet, breadth=10 feet.

A: Finding area of rectangular plot Given: length= 20ft Breadth=10ft

Q: express each measurement in feet.50 inches

A: Given: The measurement is 50 in.

Q: Isobel and Neliwe’s garage floor is 5400 mm long and 3000 mm wide.  The floor plan of Isobel and…

A: Scale can be defined as the ratio of the dimension in plan or map to the actual dimension  Scale is…

Q: express each measurement in feet.108 inches

A:

Q: Solve for the reactions and draw the shear and moment diagram. 116KN

A: PLEASE POST OTHER QUESTIONS IN DIFFERENT QUESTION

Q: Figure 20-7 Questions 1-10. 44 8. 6 38 20 24 34 Ol 76 8 80 84 88 92 10 Match the dimensions…

A:

Q: For each condensed structural formula, write a line- angle formula.

A:

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.