A simply supported steel beam of channel-type cross section is loaded by both the uniformly distributed load and the couple shown in the figure. Determine the maximum tensile and compressive stresses. 40 kN/m 40 mm 40 mm 20 kN-m 225 mm to m Im 40 mm 200 mm

A simply supported steel beam of channel-type cross section is loaded by both the uniformly distributed load and the couple shown in the figure. Determine the maximum tensile and compressive stresses. 40 kN/m 40 mm 40 mm 20 kN-m 225 mm to m Im 40 mm 200 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3
Show complete solution please.
Question: A 12 mm thick plate is connected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 9- MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is P/2 - F 8 mm 8 mm ↓ 12 mm P
4.48 A thin rod of 10 mm diameter is subjected to a tensile force of 7850 N. What are the principal: stresses and maximum shear stress? (a) 70 MPa, 50 MPa, 10 MPa (b) 100 MPa, zero, 50 MPa (c) 100 MPa, 50 MPa, 25 MPa (d) 100 MPa, zero, zero
axial compressive force P. If the stress on steel snugly fitted on a solid steel rod of 20 mm A tube of aluminium of 40 mm external diameter and 20 mm internal diameter diameter. The composite bar is subjected to a bar is 70 N/mm", the stress in the aluminium tube and corresponding value of P will be: E for steel: 2 x 10 N/mm and E for aluminium 7 x 10ʻ N/mm')
I. Problem Solving. Box your final answer. 1. Find the (a) maximum tensile and compressive bending stress in the wooden beam and (b) maximum shear stress in the shaded area of a wooden beam. 1 . 4kN 2kN 3kN 2m- A 1m 1m 2m 4m 3m 8m 5m 1m
Read the question carefully and give me all right solutions with clear calculations.
For the beam shown in Figure (1), determine: a) The stresses in rods AB and BC. The cross-sectional area of rod AB is 155 mm2, and for BC is 200 mm?. b) The average shear stress in bolt at pin A. 1500 N S5 15 m 600 N/mt m- -3 m- Figure (1)
Determine bending stress formula for the I beam
A steel latch is 6 mm thick. A force F of 3000 N is uniformly distributed as shown below. Do not consider the stress concentration! a) Determine the principal stresses at Scction B-B?. b) Determine the principal stresses at point A? 3 kN Y R30 L, A 125 09
A rectangular steel block is 3.2 inches long in the x-direction, 2.9 inches long in the y-direction, and 4.5 inches long in the z-direction. The block is subjected to a tri-axial loading of three uniformly distributed forces as follows: 48 kips tension in the x-direction, 65 kips compression in the y-direction, and 54 kips tension in the z-direction. If Poisson's ratio is 0.30 and E = 29 x 106 psi, find the uniformly distributed load that must be added in the x-direction to produced no deformation in the z-direction. Your final answer should include two decimal places