A simply supported beam with spans of LAB = 9 ft and Lac = 27 ft supports loads of w = 3.0 kips/ft and P = 28 kips. The cross-sectionaldimensions of the wide-flange shape are bf = 9.0 in., t= 0.51 in., d = 30.0 in., and tw = 0.48 in. Determine the magnitude of:(a) the maximum horizontal shear stress in the beam.(b) the maximum bending stress in the beam.byWBLBCLABAnswer:(a) Tmax=(b) OmaxksiksiC

Answered: Image /qna-images/answer/f1543446-debf-4035-b845-62970eac6656.jpg

A simply supported beam with spans of LAB = 9 ft and Lac = 27 ft supports loads of w = 3.0 kips/ft and P = 28 kips. The cross-sectional dimensions of the wide-flange shape are b = 9.0 in., t= 0.51 in., d = 30.0 in., and tw = 0.48 in. Determine the magnitude of: (a) the maximum horizontal shear stress in the beam. (b) the maximum bending stress in the beam. by W B LBC LAB Answer: (a) Tmax= (b) Omax= ksi ksi C

A simply supported beam with spans of LAB = 9 ft and Lac = 27 ft supports loads of w = 3.0 kips/ft and P = 28 kips. The cross-sectional dimensions of the wide-flange shape are b = 9.0 in., t= 0.51 in., d = 30.0 in., and tw = 0.48 in. Determine the magnitude of: (a) the maximum horizontal shear stress in the beam. (b) the maximum bending stress in the beam. by W B LBC LAB Answer: (a) Tmax= (b) Omax= ksi ksi C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

QB9
8
4. A force Q is applied to a rectangular member with a size of 3oomm x 450mm. Q is located 37-5mm left and 6omm north of the center of gravity and induces a stress of 1.75 MPa compression at point A. a) What is the axial load at Q in kN b) What is the stress induced at point C & D in MPa A B
A simply supported beam with spans of LAB = 15 ft and LBC = 45 ft supports loads of w = 3.0 kips/ft and P = 33 kips. The cross-sectional dimensions of the wide-flange shape are b= 11.0 in., tf = 0.53 in., d = 29.3 in., and tw = 0.47 in. Determine the magnitude of: (a) the maximum horizontal shear stress in the beam. (b) the maximum bending stress in the beam. A LAB Answer: (a) Tmax= (b) omax = i B W LBC ksi ksi bf
A simply supported wood beam carries a concentrated load of P = 8200 lbs as shown. The beam spans are L1 = 7 ft and L2 = 14 ft. The rectangular cross section has a width of b = 5.5 in. and a depth of d = 14 in. At section a-a, which is xa = 3 ft to the right of pin support A, determine the magnitude of the horizontal shear stress in the wood beam at point K, which is located yk = 4.5 in. below the centroidal z axis. H y Ун a Ук a B K L2 Answer: TK = i psi
A simply supported beam with spans of LAB = 5 ft and LBC = 15 ft supports loads of w = 5.5 kips/ft and P = 29 kips. The cross-sectional dimensions of the wide-flange shape are bf = 7.0 in., tf = 0.61 in., d = 26.0 in., and tw = 0.45 in. Determine the magnitude of: (a) the maximum horizontal shear stress in the beam. (b) the maximum bending stress in the beam.
1. A rectangular beam with b = 250 mm and d = 460 mm is reinforced for tension only with 3-25 mm bars. The beam is simply supported over a span of 6 m and carries a uniform dead load of 0. 680 KN/m including its own weight. Use fy=276.50 MPa and fc'=20.70 MPa. The maximum steel ratio is . 0.0128 0.0096 0.0278 0.0371 0.0167 0.0224
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 14 MPa. Answer must be in mm. Given: a = 1 m, b = 3 m, c = 2 m, P = 7 kN, and w = 2 kN/m. P KN cm w kN/m (not scaled) 290 mm a m bm b Ri R2
A cantilever beam with length of 3.2 m is reinforced with As=5720 mm^2 tension reinforcement and compression reinforcement A's =1905 mm^2 placed at 60 mm from extreme compression fiber. The effective depth is 550 mm and width of 400 mm. Use f'c=35 MPa and fy=415 MPa. 1. Calculate the magnitude of the neutral axis. 2. Determine the compressive force of the section. 3. Determine the safe concentrated live load that can be placed at the free end if the beam carries a total ultimate uniform load of 35 kN/m.
Current Attempt in Progress A simply supported wood beam carries a concentrated load of P = 9600 Ibs as shown. The beam spans are L1 = 7 ft and L2 = 14 ft. The rectangular cross section has a width of b = 6.0 in. and a depth of d = 15 in. At section a-a, which is x, = 3 ft to the right of pin support A, determine the magnitude of the horizontal shear stress in the wood beam at point H, which is located yH = 3.5 in. above the centroidal z axis. Ук a L Answer: TH = psi
A solid steel shaft supports loads PA = 570 N and PD = 430 N, as shown. Assume L1 = 250 mm, L2 = 510 mm, and L3 = 230 mm. The bearing at B can be idealized as a roller support and the bearing at C can be idealized as a pin support. If the allowable bending stress is 38 MPa, determine the minimum diameter d that can be used for the shaft.
Determine the minimum width "b" of the beam shown if the flexural stress is not to exceed 13 MPa. Answer must be in mm. Given: a = 1 m, b = 3 m, c = 2 m, P = 6 kN, and w = 3 kN/m. P kN cm w kN/m (not scaled) 250 mm am b m b. R1 R2