A simply-supported beam with length, L = 7 m, is carrying a downward uniform load, w = 42 kN/m throughout its length. The cross-section of the beam is shown in the figure with a = 495 mm, b = 28 mm, c = 23 mm, and d = 225 mm. Determine the maximum flexural stress in MPa. I a tot t d *

Q: Define roof tiles alonwith types of tiles.

A: Roof tiles are designed primarily to stay out rain, and ar historically made of regionally offered…

Q: How many Type of Interior materils.

A: Interior materials : Interior materials are the materials which are used inside the house, like…

Q: How to Install the Gypsm Board.

A: Gypsum Board: Gypsum boards or Plasterboards are one of the latest trends in the construction…

Q: construction materials and methods - How are the various types of copper water tubing identified?

A: Copper water tubing- Copper water tubing is a device that is used for heating systems, and as a…

Q: Draw a figure of door and label it

A: The figure and door is in next step

Q: assembly drawing, all parts are drawn in their working position with a completed dimension. s are In…

A: Option c ( detail ) is correct.

Q: Add/Subtract the following DMS measurements by hand. In your answer, separate each unit by a comma…

A:

Q: Draw the frontside and topview the Shape Shown

A: Asked: To draw the front, side and top view of the given shape.   The required engineering id drawn…

Q: Define differential hammer,

A: Differential hammers are the same as a double-acting hammer. these hammer having a simpler value…

Q: Define stirrup

A: Stirrup: A stirrup is a closed loop of reinforcement(steel bar) in a beam. It is called as tie-bar…

Q: Description of column and its types?

A: A column is a vertical component of the structure designed to move a compressive charge. For…

Q: create a sample company name for a “plywood made with papers”??

A: A company name is the unique name or title by which a business or organization is identified and…

Q: What are the three dividing heads used?

A:

Q: Determine the number of metal studs need to construct 128 feet of interior walls, with 6 corners, 12…

A: ANS-1) Given- corner=6 intersections=12no of 3-foot wide doorways=5Studs spacing= 16 inches or 1.33…

Q: What are the similarities and difference between the actual ASTM C143 standard and the procedure…

A: In ASTM C143, the test method includes the determination of the hydraulic cement concrete slump in…

Q: So how many inches is the minimum requirement? The explanation is hard to follow

A:

Q: 10- What is the BOM and how is it arranged on a format?

A: Note : Since you have asked multiple questions, we will solve the first question for you. If you…

Q: What is the purpose of Recarbonation?

A: The process of adding carbon dioxide to lime-softened, clarified water in order to lower the pH and…

Q: GENERAL INSTRUCTIONS: Answer the following questions comprehensively and neatly. FILE. - Enumerate…

A: Structural Elements can be different types based on the type of building; ie-RCC building, Steel…

Q: Is there anything I can learn from inspecting the bounding box that the Designer established?

A: A bounding box is used to indicate the position of the object in the image or video. It is basically…

Q: What is a sieve plate

A:

Q: Enlarges or reduces selected objects, keeping the proportions of the object. explode command…

A: Answer - Scale command Explanation- Enlarges or reduces selected objects, keeping the proportions…

Q: Define metamorphic.

A: Metamorphic:

Q: How many satellites in a full GPS constellation? O 30 O 12 O24 O 18

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: No.2 What is grain size classification？

A: According to ASTM standards.Coarse-Grained Soils: More than 50 percent retained on a 0.075 mm (No.…

Q: What is Dimensional Lumber often used for in construction projects?

A: Dimensional lumber is a wood lumber that is cut to pre defined standard sizes These are structural…

Q: Define Vertical Stresses.

A: The total vertical stress acting at a point below the surface of the ground is due to the weight of…

Q: Where is marble commonly used in building construction?

A: The marble doesn't hold heat  This is one of the most interesting facts about marble stone. The…

Q: lo" A 992 steel 14" -2" what is Mp= ? 14"

A: From the given data calculate all areas find the y bar find the Ix

Q: SFCA Given: 975 LF of 3 4" base molding. Calculate painting quantity in square feet.

A: Length of molding = 975 linear foot Dimension of molding = 3.25"

Q: Define the size of a concrete cube?

A: Cube test of concrete is one of the most important tests done on concrete. It is also known as a…

Q: NORTH 28 -12- 2 -17'-5" 7'9" l'-8" 9'-8" 15'-5" 4* - 3 EAST 24 2 5'-5" 24'- 2'4" 2'-1" 12-5" T 28'…

A: Solution I have done three questions for you  The solution of the above question is following

Q: A & C are incorrect, please re-work

A: As per question , I solve here only a and c. Find out - (a) Radius of curve  (c) Tangent length

Q: How to prepare K-omega and K-e models?

A: The k-omega (k−ω) turbulence model is one of the most commonly used models to capture the effect of…

Q: Explain basic differences of rivets, unfinished bolt, High strength Bolt connections in terms of…

A: Rivets : Rivet is a headed pin which is used for connecting two or more pieces by passing the shank…

Q: Q2/ Answer the followings with drawing sketch: A/ briefly explain what is construction joint and…

A: Construction Joint: It is type of concrete joint that is used when a new section of concrete is…

Q: The value of the smallest division on the main scale of a horizontal circle is graduated to 1/3…

A:

Q: DIFFERENT ACCESSORIES IN THE SHAPER MACHINE WORKS VERTICAL AND HORIZONTA

A:

Q: Section lining or crosshatching is also known as a …?   A. Section pattern B. Hatch pattern C.…

A: Section lining referred as cross-hatching ,is used to indicate material in the sectioned part.

Q: make a short report to stone

A: Stones or rock is a natural substance that is mined and quarried from the earth and used widely in…

Q: Please provide the enough information and definition of these construction terms:  Dam Dead line…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: List five different kinds of admixtures and their uses.

A: To List  Five different type of admixtures and their uses.

Q: Name: Match the cross-sections with the appropriate object and cutting plane for the problems shown…

A: Engineering drawing

Q: what method did you use there

A: For forces in member , method of joints have been used and for displacement calculation virtual work…

Q: UPVOTE WILL BE GIVEN. PLEASE ANSWER IN PARAGRAPH FORM. What responsibility does an engineer have…

A: Concept- An engineer plays a crucial role in the drawings and the components that actually goes into…