A simply supported beam of span Land flexural rigidity EI, carries a unit point load at its centre. The strain energy in the beam due to bending is 13 13 48 EI 192 EI (a) (c) L3 96 EI (b) (d) 13 16 EI

A simply supported beam of span Land flexural rigidity EI, carries a unit point load at its centre. The strain energy in the beam due to bending is 13 13 48 EI 192 EI (a) (c) L3 96 EI (b) (d) 13 16 EI

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A cantilever beam has the Cross-section of an isosceles triangle with a base and height equal to 1 m each. The beam is subject to 6 MN-m 1 m4. of bending moment. The moment of inertia of the section is 18 Find the maximum bending stress in MPa.
A proper cantilever ABCD is loaded as shown in figure. If it is of uniform cross-section, the collapse load of the beam will be nearly W/8 W Hagal B Mp Mp L/2 L/2 L/3 →→ D
Design the shear reinforcement for the beam shown in figure below assuming it resists an ultimate shear force at distance d from the face of the support of 450 kN. The characteristic material strengths are fok= 25 N/mm²and fm = 500 N/mm² 450 kN d= 500 mm -4H25 b= 300 mm
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
Bending Stress in Beam A symmetrical l-section is 200 mm deep and its moment of inertia about centroidal axis is 50x106 mm4. If the bending stress is limited to 100 N/mm² then bending moment it can resist will be
At which point on the design P-M interaction diagram is the design flexural strength largest? O Pure compression Pure tension Balanced failure point (CCL limit) O TCL limit Beam condition (Pn = 0) %3D //img00.zhaopin.cm
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
A steel cantilever beam 6 m in length is subjected to a concentrated load of 120 N acting at the free end of the bar. The cross section of the beam is shown below. deep. Determine the magnitude and location of the maximum tensile and compressive bending stresses in the beam. As usual, neglect the weight of the beam. 4mm 120 N 1mm 1mm 6mm 6m 1mm 4mm
A bridge girder AB on a simple span of length L = 20 m supports a distributed load of maximum intensity q at midspan and minimum intensity g/2 at supports A and B that includes the weight of the girder (see figure). The girder is constructed of three plates welded to form the cross section shown. 500 mm L= 20 m 18 mm 1600 mm 500 mm (a) Determine the maximum permissible load q based upon an allowable bending stress oallow = 130 MPa. Round to the nearest tenth. kN Gmax = (b) Determine the maximum permissible load q based upon an allowable shear stresS Tallow = 55 MPa. Round to the nearest tenth. kN Gmax m
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
The beams ABD and DE are joined by a hinge at D. Select the lightest allowable W-shape for beam DE if its working stress in bending is 120 MPa. Also calculate the actual maximum bending stress in beam DE.
8-46. The wide-flange beam is subjected to the loading shown. Determine the stress components at points A and B and show the results on a volume element at each of these points. 500 lb ↓ 2 ft 2 ft 2500 lb B 2 ft 4 ft 3000 lb 0.5 in.- Prob. 8-46 B 6 ft- 0.5 in. 1-4 in T 4 in. 12 in. 0.5 in.