A simply supported beam L meters long carries a uniformly distributed load of  6.8 KN/m  over its entire length and has the cross section shown .  If the L used will cause a maximum flexural stress of 35 MPa, what maximum shearing stress in MPa is then developed?

Q: A  timber beam is 15 cm deep by 10 cm wide, and carries a central load of 30 kN at the centre of a 3…

A: Given:- deep=15cm wide=10cm load=30kN span=3m flat steel plate width=10cm E steel=200GN/m2 E…

Q: The horizontal stress at the centroid of a PSC beam of a rectangular section 130 mm × 250 mm is 7.5…

A: Given data in question PSC beamCross section 130×250 mmStress 7.5 N/mm2Shear force 70 kNTo find out…

Q: A simply supported beam of span 1 carries a UDL of w kN/m over whole of span. What will be the…

A: For a simply supported beam of span l carries UDL of w kN/m over span LTo find the strain energy…

Q: A beam supported on a 8m span carries a uniformly distributed load of 30 kN/m over the middle 5m.…

A:

Q: A beam has a uniform concentrated load (Pu) at midspan and has a fixed support at both end. If the…

A:

Q: An 2014 T-6 aluminium flag pole with a hollow rectangular section experiences a wind force of 750 N…

A: ultimate tensile strength : A tensile test is commonly used to determine ultimate tensile strength,…

Q: A beam simply supported over a span of 9m is loaded with a uniformly distributed load of 48 kN/m.…

A: Given: The length of the beam is 9 m. The UDL on the beam is 48 kN/m. The width of the beam 200 mm.…

Q: The ratio of maximum shear stress to average shear stress of a circular beam is: (a) (c) 2/3314 (6)…

A: given- Circular beam, the ratio of maximum shear stress to average shear stress is required.

Q: Problem 1. Classify the pre – stressed beam (shown in the figure) at midspan if it is uncracked,…

A:

Q: A simply supported beam is carrying a unıform load. It the beam prop below, what is the final stress…

A: Introduction: Prestress of concrete is basically concrete in which internal stress of suitable…

Q: B\\ A simply supported post-tension beam as shown below it's carries a uniformly distributed service…

A: The post-tensioned beam is a horizontal member of the building or structure in which the steel wires…

Q: Q1: A Steel Universal beam of 305x102UKB33 is subjected to an axial compressive force of 200kN. The…

A: The given dimensions of the beam are:Depth (D) = 305 mmWidth (B) = 102 mmSectional Area Given…

Q: In a stressed body, an elementary cube of stresses equal to 15 kN/cm2 and 9 kN/cm2 are observed on…

A: Given data : σX=15 KN/cm2σY=9 KN/cm2ζXY=4 KN/cm2

Q: A decorative concrete beam is simply supported over a span of 16 m. The beam weighs 4 kN/m and the…

A:

Q: Arectangular pre stressed concrete beam 450 mm 700 mm is simply supported having a span of m. The…

A:

Q: 20.14 (B/C). An I-section has the dimensions shown in Fig. 20.18a, and is subjected to an axial…

A: given question shear stress = 56MN/m2 G= 82N/m2 since beam is symmetric about both axisso centroid…

Q: is 35ksl. If Its aross-section is rectangular, determine its required thickness.

A: Take moment about A :∑ MA=0FBCsin608ft-2882=0FBC=8sin60FBC=9.2376kips

Q: Situation 2. A 4m cantilever beam has a live load of 50 kN at its free end. A. . Draw the shear…

A:

Q: The maximum bending stress (in MPa)

A: Given data, Simply supported beam having,width,b= 100 mm=0.1 mheight,h= 200 mm=0.2 mlength,l= 4…

Q: Find the maximum tensile and compressive flexure stresses for the cantilever beam shown in Fig. 4…

A: Given : This is a Solid mechanics problem where we have to find the Max, tensile and compressive…

Q: A propped 10 m cantilever beam is required to carry a load of 100 kN at midspan. If the yield stress…

A:

Q: Given. A two-story Fig. forms part of the building frame system in SDC E. The axial loads on the…

A:

Q: A timber beam 150 mm wide by 250 mm deep is to be reinforced at the top and bottom by steel plates…

A: Given : Width of beam = 150 mm Depth of beam = 250 mm Thickness of steel plate = 10 mm Moment = 40…

Q: The service loads acting on a structural member are as follows: DL = 80 kN/m; WL = 50 kN/m The limit…

A:

Q: Highway Loads: Uniform Load = 70 kN/m Concentrated Load = 120 kN   Calculate for the maximum…

A: The uniform load is 70 kN/m. The concentrated load is 120 kN.   Let’s apply a unit load at point D.…

Q: A reinforced concrete beam is subjected to the following bending moments. Moment due to dead load =…

A:

Q: Consider a circular beam 8 m long and 600 mm in diameter subjected to uniformly distributed load of…

A: For given circular beam,Length,L= 8 mDiameter, D= 600 mmLoading, 30 kN/m uniformly distributed load

Q: A simply supported beam has a concentrated load at midspan. If the beam properties are given below,…

A:

Q: 100 mm x 300 mm x 5 m long simply supported beam carries a uniform load of 6kN/m over its entire…

A:

Q: m wide by 290 mm high ro at the free end to 130

A:

Q: yield stress is 12 MPa and a factor of safety of 1.5 inst yielding is desired, what is the required…

A:

Q: In a rectangular beam of size 200 mm x 400 mm, if the ultimate shear force due to design load is 80…

A: Width b=200 mm, Depth d=400 mm, Ultimate shear force due to design load=80 kN,

Q: A square steel slab base of area 1m2 is 11

A: follow given the below

Q: A simply supported uniform beam with a span of 4m supports a uniformly distributed load of 100kN/m.…

A:

Q: different cross section designs (WWF and reactangle), a) Calculate the max tensile stress and shear…

A: given, two beams WWF section (which is symmetrical about mid-section) and rectangular section Mmax =…

Pressure and Stress