A simple pendulum is pivoted at O and is free to swing in the vertical plane of the plate. If the plate is given a constant acceleration a =2.7 m/s? up the incline e = 26°, find the steady angle ß assumed by the pendulum after all initial start-up oscillations have ceased.Neglect the mass of the slender supporting rod.Answer: B = i

we have to determine the steady state angle of the pendulum bob.

A simple pendulum is pivoted at O and is free to swing in the vertical plane of the plate. If the plate is given a constant acceleration a = 2.7 m/s² up the incline e = 26°, find the steady angle ß assumed by the pendulum after all initial start-up oscillations have ceased. Neglect the mass of the slender supporting rod.

A simple pendulum is pivoted at O and is free to swing in the vertical plane of the plate. If the plate is given a constant acceleration a = 2.7 m/s² up the incline e = 26°, find the steady angle ß assumed by the pendulum after all initial start-up oscillations have ceased. Neglect the mass of the slender supporting rod.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. Consider the 5-1lb bar with length of 2½ feet and width of 2 inches. Small frictionless bearings are mounted to the ends, constraining the motion of the bar to the horizontal x and y slots. The bar starts at rest at positioned at 0= 45°. If an angular acceleration of 3 rad/s² is desired, what moment M must be applied to the bar? What are the reaction forces at A and B at that instant? Additional question: Does the width of the bar matter, or is it appropriate to consider the bar as a slender rod? Consider errors of less than 2% negligible.
A simple pendulum is pivoted at O and is free to swing in the vertical plane of the plate. If the plate is given a constant acceleration a = 4.2 m/s2 up the incline θ = 30°, find the steady angle β assumed by the pendulum after all initial start-up oscillations have ceased. Neglect the mass of the slender supporting rod.
The position of the small 0.68-kg blocks in the smooth radial slots in the disk which rotates about a vertical axis at O is used to activate a speed-control mechanism. If each block moves from r = 162 mm to r = 200 mm while the speed of the disk changes slowly from 272 rev/min to 382 rev/min, design the spring by calculating the spring constant k of each spring. The springs are attached to the inner ends of the slots and to the blocks.
please define the system and provide the free-body diagram with x-y-axis
A 20kg slender rod AB is pinned to a roller at A that slides freely along the slot as shown in the figure below. The rod is released from the rest at an angle of 30. At the same time, a couple moment of M = 5 N.m in clockwise direction is applied at its centre of gravity. If immediately after the release the acceleration of the roller at A is 43m/s, determine the reaction forces at the pin connection at Point A.
The figure shows the cross section of a uniform 239-lb ventilator door hinged about its upper horizontal edge at O. The door is controlled by the spring-loaded cable which passes over the small pulley at A. The spring has a stiffness of 16.6 lb per foot of stretch and is undeformed when 8-0. If the door is released from rest in the horizontal position, determine the maximum angular velocity reached by the door and the corresponding angle 0. Answer: @max 4.2¹ rad/sec at 8-i
The cylindrical peg has a mass m and is confined to move along the smooth horizontal slot due to the rotation of the lever arm. (The figure shows the system as seen from above.) The angular rotation of the lever arm is e(t), wheret is in seconds. Obtain the equations of motion for the peg. r(0)
The link AC (6 kg) rotates in the vertical plane about the point B. A spring (k = 600 N/m, points C to D) of unstretched length 225 mm is fixed to the link as shown. If the link is released from rest in the position shown below, determine its angular velocity after it has rotated 90°. You may take the moment of inertia of the link AC about its mass center as Igac =÷ml?. 180 900 mm
4. The uniform slender rod has a mass m= 20 kg and length L = 0.5 m. As the frame accelerates forward the rod is held in the position shown at a steady angle 0 = tan (3/4) by the stop at A. Determine the magnitude of the reaction force at stop A if the acceleration is a = 6 m/s. A = a L. A
The clock pendulum consists of the slender rod of length I and mass m and the bob of mass 7m. Neglect the effects of the radius of the bob and determine lo in terms of the bob position x. Calculate the ratio R of Io evaluated for x = ³/1 to Io evaluated for x = 1. 7m x m 1
The uniform 30-kg bar AB hangs from a pin attached to the 50-kg homogeneous disk C. The system is at rest when the horizontal force P =200N is applied. Find the angular accelerations of the disk and the bar immediately after P is applied.
The uniform 99-lb log is supported by the two cables and used as a battering ram. If the log is released from rest in the position shown, calculate the initial tension induced in each cable immediately after release and the corresponding angular acceleration a of the cables. Assume a = 3.9 ft, b = 2.9 ft, c = 1.3 ft, e = 61°. a a C Answers: TA = i 21.6 Ib TB = i 64.9 Ib a = 4.00 rad/sec?