A shunt motor draws current of 60 A from a 120V source rotating at 1800 RPM. If the armature resistance is 0.2 Ohms and the field resistance is 50 Ohms Find: The fleld current B. The armature current. C. The counter EMF. D. The developed power in H.P E. The developed Torque.

A shunt motor draws current of 60 A from a 120V source rotating at 1800 RPM. If the armature resistance is 0.2 Ohms and the field resistance is 50 Ohms Find: The fleld current B. The armature current. C. The counter EMF. D. The developed power in H.P E. The developed Torque.

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter31: Wound Rotor Motors

Section: Chapter Questions

Problem 10RQ

See similar textbooks

Similar questions

Q1/ B/ A (220 V) series de motor runs at (400 rpm) and its useful torque is (100 Nm). If its efficiency at this load is (80% ), find the load current.
As shown in the figure below, this is a speed regulation method for DC separately excited motor. a) What is the speed regulation method? b) What are the characteristics for this speed regulation method? B no Ra le lo R: '3 E R3 Tr. T
Q3) A 220 V d.c series motor has armature and field resistances of 0.15 Q and 0.10 Q respectively. It takes a current of 30 A from the supply while running at 1000 rpm. If an external resistance of 1 Q is inserted in series with the motor, calculate the new steady state armature current and the speed. Assume the load torque remains constant.
A 480V, 3-phase, 50Hz 6-pole Induction motor with a rated power of 10KVA. (i) Calculate the synchronous speed in rad/sec (ws) (ii) Determine the rotor speed in rpm, if the % slip is 2.5%
The reason why the starting torque of a series motor is higher than a shunt motor is because the series motor has O more current flowing through its armature O a stronger net magnetic field around both coils during the inrush of stator current
need help on this queation，thanks
Question 2 Beli vifth Slack side Motor (imprut) Tight side Beli thickpess\ Centre distance Figure 2 Figure 2 shows an open flat belt drive connected to a motor and a pulley. The motor transmits 20 kw to the connect pulley of 450 mm diameter and is rotating at 850 r/min to a second pulley rotating at 400 r/min. The distance between pulley centres is approximately 2 m. The belt is 6 mm thick and has a density of 970 kg/m. The maximum stress in the belt is not to exceed 2,7 MPa. The coefficient of friction for both pulleys is 0,3. Determine: 2.1. The diameter of the second pulley. 2.2. The length of the belt. 3.3. The width of the belt taking centrifugal tension into account.
I need the answer as soon as possible
In speed coontrol of dc motor, the potentiometer is used as a control element. Select one: True False
armature rotated at @ An 8- pole, lap wound 350 rpm is required to generate 260V. The useful Flud per pale is No of the armature Conductors. c.oS Wb, Calculate the totul
Q5.A 50 HZ, 4-poles star connected induction motor has a slip=0.04 & Pout=20hp find: (1).Synchronous speed in r.p.m.(ns) 2)rotor speed in r.p.m(n;) 3). Rotor frequency (f:). 4Loud torque, 5) Rotor frequency Note: 1hp=746watt
QUESTION 8 Consider the equations of motion of an armature controlled DC motor given by Jw(t)+bw (t) Ki(t) = -Tfriction - Tload (t) di (t) + Ri (t) + Kw (t) = Vin (t), dt where vin(t) is the input voltage and Tload(t) is the input load torque. The outputs are the armature current i(t) and the motor speed w(t). The steady-state response of motors are specified by nominal voltage, stall torque, stall current, no load speed, and no load current. At steady-state operation, the motor equations satisfy bo) -Ki =-T -T. fric load Ri +Kov_- 55 55 The stall torque is the load torque required stead-state speed of the motor is zero. The stall current is the armature current when the motor speed is zero. The no load speed is the speed of motor when the load torque is zero. The no load current is the current when the load torque is zero. What is stall torque for this motor in N-m? Keep 3 significant figures, and do not include units. Use Scientific notation. The constants are given below. Nominal…