A shunt generator supplies a 33kW load at 200V through cables of resistance, R = 106m2. If the field winding resistance, Rf =580 and the armature resistance, Ra =48m2. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,

A shunt generator supplies a 33kW load at 200V through cables of resistance, R = 106m2. If the field winding resistance, Rf =580 and the armature resistance, Ra =48m2. Determine the following below: The terminal voltage is, The e.m.f. generated in the armature is,

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A 6 pole wave wound d.c. shunt generator has 500 conductors. A generator delivers 50 kW of power at 250 voltage at full load. The resistance of the field circuit is 125 2. Actual brush shift is 10°. Then find the demagnetizing and cross magnetizing ampere turns per pole and how many additional turns must be wound on each pole to eliminate the demagnetizing effect.
9. How does the concept of magnetic saturation impact the performance of transformers and inductors?
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
A single phase full wave AC voltage controller has a resistive load of 5 ohms and an input voltage of Vs = 220 V (RMS), 50 Hz. The delay angles of both thyristors are set to 90 degrees. The maximum power that can be delivered to the load is: Select one: a. 5.65 kW b. 9.68 kW c. 11.52 kW d. None of these
Q9. What is the basic principle that a cage winding can be represented by a three-phase winding? Give your explanation.
A 250 V d.c. shunt generator has 1250 watts constant loss. Find out load current at maximum efficiency. Take armature resistance as 0.1ohm.
Full solutions for the question with explanation
The resistance of the field winding(copper wire) of a DC machine is 0.25 ohm at 25°C. When operating at full-load, the temperature of the winding is 75 °C. The temperature coefficient of resistance of copper is 0.00427 per °C at 0°C. Find the resistance of the field winding at full-load.
(Draw the Circuit Diagram) A self-excited shunt generator has a field resistance of 60 ohms. When the generator delivers 6 kW, the terminal voltage is 120 V, while the generated emf is 133 V. Determinethe armature resistance
The total flux per pole in the air-gap of a 50-Hz alternator is 0.06 Wb. The flux-density distribution is given by T. The coil-span is 4/5 of a pole pitch. Determine the rms emf per armature turn. Find also the emf per armature turn when the flux were assumed to be sinusoidally distributed.
5.33. A 12-kW, 120-V dc series generator has a series field resistance of 0.05 N. The generated emf is 135 V when the generator delivers the rated load at its rated terminal voltage. What is the armature resistance? If the load is reduced to 80% of its rated value at the rated voltage, what is the induced emf in the armature? If the generated emf is 130 V and the generator is supplying 4.167 kW, what is the terminal voltage?
a) Define what the term "permeability" means. Explain why this is an important parameter in designing transformers. b) A maximum current of 60 A flows in a copper conductor with cross-sectional area, A. u7 ond o recistivity of 20 n0. m. A 250 m cable is being used on a 240 V DC circuit to