A short post constructed from a hollow circular tube of aluminum supports a compressive load of 26 kips (Fig. 1-5). The inner and outer diameters of the tube are d, = 4.0 in. and d, = 4.5 in., respectively, and its length is 16 in. The shortening of the post due to the load is measured as 0.012 in. Determine the compressive stress and strain in the post. (Disregard the weight of the post itself, and assume that the post does not buckle under the load.)

A short post constructed from a hollow circular tube of aluminum supports a compressive load of 26 kips (Fig. 1-5). The inner and outer diameters of the tube are d, = 4.0 in. and d, = 4.5 in., respectively, and its length is 16 in. The shortening of the post due to the load is measured as 0.012 in. Determine the compressive stress and strain in the post. (Disregard the weight of the post itself, and assume that the post does not buckle under the load.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

مقاومة المواد
The bronze bar 3.42 m long with a cross-sectional area of 627 mm2 is placed between two rigid walls. At a temperature of -14 °C, there is a gap Δ = 2.36 mm, as shown in the figure. Find the temperature at which the compressive stress in the bar will be 34.22 MPa. Use α = 18 × 10-6 /°C and E = 80.32 GPa. Round off your answer to two decimal places.
Rod(1), rod (2) where 1, 2 rod numbers not the graded question
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.24 mm the values of elastic modulus for steel is 221 MPa. Take H1 = 4 cm, H2 is 2 x 2 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. = 9 cm, top bar (R) IP Solution: R cm x RCm Steel bar i) Magnitude Force, P = H1 cm ii) Stress-induced in the top bar = Q cm x Q cm Steel bar H2 cm iii) Stress-induced in the bottom bar =
When an axial load is applied to the ends of the bar shown in the figure, the total elongation of the bar between joints A and C is 0.17 in. In segment (2), the normal strain is measured as 1,450 uin./in. Assume L₁ - 45 in. and L₂ - 94 in. Determine (a) the elongation of segment (2). (b) the normal strain in segment (1) of the bar. P A Answers: L₁ (a) in.₂ = i (b) £₁ = i B (2) L2 in. uin./in.
2 3.0 m 175 KN 2.5 m 200 KN (1) (2) 46 mm 175 kN 30 mm Problem 3 A compound axial member consists of steel (E=200 GPa) segment (1) and brass (E=120 GPa) segment (2). a) Compute the total deformation of the compound member for the loading shown (in mm). b) Sketch an internal normal force diagram c) Calculate the average axial stress in segment 2
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.89 mm the values of elastic modulus for steel is 209 MPa. Take H1 = 7 cm, H2 = 11 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. i) Magnitude Force, P in(N) = ii) Stress-induced in the top bar in(N/mm^2) = iii) Stress-induced in the bottom bar in(N/mm^2) =
please help answer and explain
Its urgent