A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load)

A short post constructed from a hollow circular tube of aluminum supports a compressive load of 250 kN (see figure). The inner and outer diameters of the tube are d1 = 9cm and d2 = 13cm, respectively, and its length is 100 cm. The shortening of the post due to the load is measured as 0.5 mm. Determine the compressive stress. (Disregard the weight of the post itself, and assume that the post does not buckle under the load)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

#12
9
.
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
please recheck your final answer.
A flat steel bar, 26 mm wide by 3 mm thick and 1.7 m long, is bent by couples applied at the ends so that the midpoint deflection is 21 mm. Compute the maximum stress in the bar. Use E = 240 GPa. Answer must be in MPa.
Please show all steps so your process is easy to follow
A rigid bar XYZ as shown in the figure below is hinged at X and is supported at Y. If the stress in the steel rod is limited to 150 ksi, determine the largest possible load P that can be applied at point Z.
02: The rigid platform has negligible mass and rests on two steel bars, each 250.00 mm long. The center bar is aluminum and 249.90 mm long. Compute the stress in the aluminum bar after the center load P= 400 kN has been applied. For each steel bar, the area is 1200 mm2 and E= 200 GPa. For the aluminum bar, the area is 2400 mm2 and E 70 GPa Rigid platform Steel Ahmum Steel
6- A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 11 mm and an elastic modulus of E = 78 GPa. The steel rod has a diameter of 16 mm and an elastic modulus of E = 200 GPa. Assumea = 4.1 m, b= 1.2 m, and c= 1.2 m. What is the magnitude of load P that is necessary to displace point A 12 mm to the left? a (1) (3) A B (2) Answer: P = i kN