A short link has a thermal rating of 1.0 MVA, and a phase impedance of 140 /50.7°.The receiving end voltage needs to be kept at 11 kV, and the sending end voltagemust not be more than 10% above this when the link is fully loaded. Sketch a phasordiagram for the loaded link, and hence determine the active and reactive powers thatcould be delivered in this condition.947 kW; 321kVAr lagging

Answered: A short link has a thermal rating of…

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter14: Power Distribution

Section: Chapter Questions

Problem 14.6P

See similar textbooks

Similar questions

A three-phase, 60-Hz, untransposed transmission line runs in parallel with a telephone line for 20 km. The power line carries a balanced three-phase rms current of Ia = 3202 – 240°A. The line configuration is as shown in figure. Assume zero current flows in the ungrounded telephone wires. Find the magnitude of the voltage induced in the telephone line. = 32020°A, Ī, = 3204–120°A, and a 4 m 4 m 5 m d G2 mO
Q2: The constants of a 275 KV transmission line are A = 0.8525° and B = 200275° 0/phase. Draw the circle diagram to determine the power and power angle at unity power factor that can be received if the voltage profile at each end is to be maintained at 275 KV. What type a rating of compensating equipment will be required if the load is 150 MW at unity power factor with same voltage profile. (5.5 mark)
4. A CT with an excitation curve given in the figure has a rated current ratio of 500:5 A and a secondary leakage impedance of 0.1 +j0.5 ohms. Calculate the CT secondary output current and the CT error for the following cases: a.) The impedance of the terminating device is 4.9 +j 0.5 ohms and the primary CT load current is 400 A. b.) The impedance of the terminating device is 4.9 +j0.5 ohms and the primary CT load current is 1200A c.) The impedance of the terminating device is 14.9 + j 1.5 ohms and the primary CT fault current is 400 A. d.) The impedance of the terminating device is 14.9 + j 1.5 ohms and the primary CT fault current is 1200 A w 100 80 60 40 20 2 4 6 10 Secondary exciting amps-, Secondary exciting volts-E'
Q A 50 Hz, 13.6kv, 3-phase arternator with grounded neutral hasinductance of 12 mH per phase and is connected to busbar 16]through a circuit breaker. The capacitance to earth between thealternator and the location of circuit breaker is o.03pF per phase.Neglect the resistance of the alternator. Determine the following:i) Maximum value of re-striking voltag. ."ro". the contactsof circuit breaker.i1) Frequency of transient oscillationsiii) Maximum value of RRRVir') Average RRRV upto the first peak of transientoscillations.
Consider the 500 kV, three phase bundled conductor line as shown in the figure below. Find the line to neutral capacitance. 0.5 m 30 mm (0) (O to Ine 15 m 15 m
Please and thank you
400Ω A k=0.9 600Ω B k=0.8 66Ω 600Ω
Develop a small-scale equivalent transmission line pi model (per phase) of the transmission lines with the specification given in table 1. The conductors are placed with a flat horizontal spacing of 7.25 meters. Consider that the load connected against the line 125MW at 0.85 lagging power factor. You are required to develop an equivalent model for a maximum 220V (RMS) sending and receiving end voltage and a maximum of 5A load current. Sr. NTDC Transmission Line Length Conductor No. Туре 220 kV DG Khan-Loralai Transmission Line (227 km) 227km Pheasant TABLE AJ Electrical characteristics of bare aluminum conductors steel-relnforced (ACSR)+ Reniertance Reactance per conductor 1-ft apacing. 60 Ha Ae, 60 Ha Capaitive Aluminum ares, emil Layers of Outaide aluminum diameter, in a/1,000 ft soC, D/ml GMR Induetive Stranding AL/8t De, 20°C. 20C, a/mi Code word D. t Ma-mi Waswing Partridge Ostrieh Merlin Linnet Oriole Chickndee Ibin Pelienn Flicker Hawk 266,800 206,800 300,000 336, 400 336.400…
Obtain three zone setting for (i) a reactance relay and (ii) a mho relay of 60° from the following data: CT: 400/1 A PT: 132 kV/110 V Impedance for the first section is (2.5 + j5) ohms (primary) and that of second section (3.5 + j7) ohms (primary). The first zone covers 80% of the first section, the second zone covers the first section plus 30% of the second section and the third zone covers the first section plus 120% of the second section.
4. A 4160V, three phase source, 4-wire supplying an unbalanced three phase load. The unbalanced connected load are: Zan = 150/53.13° ; Zbn = 150-53.13° ; Zen = 1500° Assuming positive sequence and the reference is the line voltage "a", determine: a. the line current "a" b. the line current “b” c. the line current "c". d. the total real power e. the total reactive power f. the total apparent power g. the overall power factor. h. the neutral current.
A 220 kV, three phase transmission line is 50 km long. The resistance per phase is r 2 per km and the inductance per phase is L mH per km. The shunt capacitance is negligible. If the line supplies a three-phase load of 229 MVA at 0.8 power factor lagging at 220 kV with an efficiency of 97.13% and a voltage regulation of 4.7581%. Use the short line model to find the line resistance and inductance of the line.
High voltage engineering subject

SEE MORE QUESTIONS

Recommended textbooks for you

Power System Analysis and Design (MindTap Course …

Electrical Engineering

ISBN:

9781305632134

Author:

J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:

Cengage Learning