A shop crane consists of a boom AC that is supported by a pin at A and by a rectangular tension bar BD, as shown in Fig. 1.1. Details of the pin joints at A and B are shown in Views a-a and b- b, respectively. The tension bar BD has a width w = 1.5 in. and a thickness t = 0.5 in. If the vertical load at C is P = 5 kips, then determine the following: 1. What is the calculated normal stress ? in the bar BD. 2. Determine the calculated shear stress? at pins A, B, and D. Assume that the pins are 3/4" in diameter. 4 ft Ja 6 ft 5 P=5 kips View b-b View a-a Figure 1.1 Shop Crane

A shop crane consists of a boom AC that is supported by a pin at A and by a rectangular tension bar BD, as shown in Fig. 1.1. Details of the pin joints at A and B are shown in Views a-a and b- b, respectively. The tension bar BD has a width w = 1.5 in. and a thickness t = 0.5 in. If the vertical load at C is P = 5 kips, then determine the following: 1. What is the calculated normal stress ? in the bar BD. 2. Determine the calculated shear stress? at pins A, B, and D. Assume that the pins are 3/4" in diameter. 4 ft Ja 6 ft 5 P=5 kips View b-b View a-a Figure 1.1 Shop Crane

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2.1.Write the Equation and describe the style in the latitude of the structure
An over hanging beam ABC of length 10 m (including over hang portion) is shown in the figure below. The ratio of ILD ordinates at C to ILD ordinates at B for the shear force at B is A B 7 m 3 m-
1. For the given loaded beam shown, a. b. C. d. 40 kN-m B Im Im C 12 kN/m 3 m 2m E 125 -15- 15 145 Sketch the shear and moment diagram. Determine the maximum tensile bending stress in the beam. Ans. Determine the maximum compressive bending stress in the beam. Ans. Determine the maximum horizontal/transverse shear stress in the beam. Ans. dire lengt
H.W. 1:An axial member consisting of two polymer bars is sup- ported at C, as shown in Figure area ol 540 mm and an elastic modulus of 28 GPa. Bar (2) has a cross-sectional area of 880 mm2 and an elastic modulus of 16.5 GPa. Determine the deflection of point A relative to support C. . Bar (1) has a cross-sectional 50 kN Om She 35 kN (1) (2) 50 kN 0.85 m 1.15 m FIGURE
Picture given below; There is a uniformly distributed load on the beam, which is made of Al2010 (T4) alloy T-profile and is connected to the "A" sliding bearing with "B" joint fixed support. Safe compression and tensile normal stress of the beam is Gemn=100 MPa. q=23 kN/m C-C Kesiti + 15 | 18 | 15 q=23 kN/m A유 30 cm 100 cm 150 cm 16 KİRİŞ T- PROFİLİ 74 Ød MAFSAL PİMİ Ölçüler mm dir. 104 S-1) Calculate the support reactions by drawing the SCD of the beam. S-2) The beam; a) Draw the shear force diagram, b) Moment diagram and determine the maximum moment. S-3) Find the x and y axis coordinates of the center of gravity of the cross-sectional area of the beam whose T-profile dimensions are given. S-4) Find the moments of inertia with respect to the vertical and horizontal axes passing through the center of gravity of the T-profile cross-section area. S-5) Find the tensile and compression stresses caused by bending on the beam with T-profile and check the safe carrying condition of this…
Note: Do it your own. Don't copy from other experts solution. Kindly give me right solution with clear calculations
This a mechanics of material question please show all steps so your approach is easily followed. Please show Free body diagram, what is given, and what the problem is asking for. Thank you
Remember to show all units and provide a step by step solution showing all work. Draw and label diagrams.Use the formula sheet.
From the figure as shown, the cable BC supports the horizontal bar AB. Compute the shear stress at the hinge support at A having 20 mm Ø and at the pin support at B which has 30 mm Ø pin. The given views show how many of shear can be produced. Use 2 decimal places in every solved value. Pls include fbd.
What is the maximum absolute shear for the following beam and load group? Use L = 21, a = 3, b = 4, P1 = 2, P2 = 4, and P3 = 4. ܢܢܢܢܢܢܢ L P₁ P2 미미 a b P3
Determine the shear and moment diagrams of the following beams loaded as shown on short size bond paper. Show your solution.
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear. 2. Determine the moment of inertia, I, of the section in mm^4.