A shaft is required to fail when the torque on the shaft is 182 N-m. Find the suitable diameter of the shaft if the maximum shear stress is 50 . A shaft is required to fail whenthe torque on the shaft is 182N-m. Find the suitablediameter of the shaft if themaximum shear stress is 50N/mm2.О а. 26.46 mmO b. 2.646 mО с. 26.46 mO d. 2.646 mm

Answered: Image /qna-images/answer/d7d96cca-0473-4c35-88c4-88b319fa0653.jpg

Answered: A shaft is required to fail when the…

A shaft is required to fail when the torque on the shaft is 182 N-m. Find the suitable diameter of the shaft if the maximum shear stress is 50 .

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please answer by moment area method
Consider the maximum allowable shear stress in the shaft. Calculate the minimum diameter required for the shaft. Answer: d = i in.
he compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T in kN-m that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel.
3. Find the diameter of a solid steel shaft to transmit 27 kW at 300 r.p.m. The ultimate shear stress forthe steel may be taken as 360 MPa and a factor of safety as 8. If a hollow shaft is to be used in placeof the solid shaft, find the inside and outside diameter when the ratio of inside to outside diameters is0.5
The shaft whose torque varies from 2100- 6000 in- lbs has 1 and one- half inch diameter and 60000 psi yield strength . Compute the shaft variable component stress.
Calculate the normal stress and the shear Stress at Points C and D The shaft is hollow; inner and outer radlus values are shown below on paper. N = 1000N M = -900N V = -650N Torque = 90N - Mr = 13Mm
B5
The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 74 mm and G = 33.05 GPa. For the steel segment BC, the diameter is 47 mm and G = 84.69 GPa. Given that a = 2.18 m and b = 1.33 m, compute the largest torque T (in Nm) that can be applied as shown in the figure if the maximum shear stress is limited to 60.08 MPa in the bronze and 82.03 MPa in the steel. Round off the final answer to two decimal places
A drive shaft running at 2500 rpm has outer diameter of 60mm and innerdiameter of 40mm. The allowable shear stress in the shaft is 35MPa. Determine themaximum power that can be applied. Present drawings/FBD’s illustrating your solution.
The two solid shafts are connected by the gears shown. The motor constantly supplies 20 kW of power at 15 Hz to system at A. The yield shear stress is 140 MPa for shaft (1) and 220 MPa for the shaft (2), and over all factor of safety is 2. a) Find the diameter of both shafts. b) If the modulus of rigidity of shaft (2) G is 77.2 GPa, calculate the relative angle of twist D with respect to C. 30 teeth B (1) 48 teeth Tp 0.8 m
The shear modulus of the solid steel shaft is G = 11 x 10° ksi. Motor A is directly coupled to the shaft and delivers 3 hp while rotating at 1800 rpm (revolutions per minute). Gears B, C, and D remove the powers indicated in the figure. Given the following two criteria, determine the required diameter of the shaft to the nearest 1/s in. (1) The maximum shear stress must not exceed Tallow = 9 ksi. (2) In order to prevent binding or interference in the attached machin- ery, the angle of twist of gear B with respect to gear D must not exceed 1°. 1.25 ft 1.0 ft 3 hp 1.5 ft 1 hp 0.5 hp 1.5 hp
I need answer within 5 minutes please please with my best wishes