A seven-story office building has 15 adjacent offices per floor. Each office contains a wall socket for a terminal in the front wall, so the sockets form a rectangular grid in the vertical plane, with a separation of 4 m between sockets, both horizontally and vertically. Assuming that it is feasible to run a straight cable between any pair of sockets, horizontally, vertically, or diagonally, how many meters of cable are needed to connect all sockets using a. (a) a star configuration with a single router in the middle? b. (b) an 802.3 LAN?

A seven-story office building has 15 adjacent offices per floor. Each office contains a wall socket for a terminal in the front wall, so the sockets form a rectangular grid in the vertical plane, with a separation of 4 m between sockets, both horizontally and vertically. Assuming that it is feasible to run a straight cable between any pair of sockets, horizontally, vertically, or diagonally, how many meters of cable are needed to connect all sockets using a. (a) a star configuration with a single router in the middle? b. (b) an 802.3 LAN?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Need Q 1,2 please
Consider the following function F(w, x, y, z) = [1(0, 1, 2, 3, 5, 10, 13, 14, 15) 1. Minimize the function. 2. Identify all static hazards of the circuit. 3. Design a hazard free circuit.
• Calculate the weight matrix for a Hopfield network to store the pattern [1 -1 1-1] • Which of the following statements is NOT true for a Hopfield network? A. The output of the units is often specified by a bipolar step function. B. The weight matrix is symmetric that is, wy w for all units į and j. C. A unit can be connected to itself-that is, we not = 0 for all units i
A fixed beam is subjected to a uniformly-distributed load with an intensity of f = 10 N/mm length of L = 200 mm. Now determine the support reaction forces, internal shear forces and moments, then plot its internal shear force and moment diagram. f[N/m] L 1. Define the paramters, use L and f as the variables y X
1. For traffic signal control in a T junction: Provide the allocation List Draw the Grafcet and obtain the grafcet equation Develop the ladder programming from the grafcet Figure below shows the T junction with three traffic signals. Each traffic light cycles through red (i.e. stop) time depends on the other two signals, red & amber (i.e. get ready to go) for 5 seconds, green (go) for 20 seconds, and amber (stop if safe to do so) for 5 seconds. major road Hoo SIGNAL 3 3 2 SIGNAL 2 SIGNAL I minor road Figure
A seven-story office building has 15 adjacent offices per floor. Each office contains a wall socket for a terminal in the front wall, so the sockets form a rectangular grid in the vertical plane, with a separation of 4 m between sockets, both horizontally and vertically. Assuming that it is feasible to run a straight cable between any pair of sockets, horizontally, vertically, or diagonally, how many meters of cable are needed to connect all sockets using a. (a) a star configuration with a single router in the middle? b. (b) an 802.3 LAN?
COMMUNICATION AND COMPUTER NETWORKS
Data communication Suppose that the spectrum of a channel is between 8 MHz and 10 MHz, and the intended capacity is 8 Mbps. a. What should be the signal-to-noise ratio (SNR) to obtain this capacity? Constant values= c=3x^10°m/s, k=1,38x^10231/K I
25. To design analogue computer for solving the first-order system: Y(s) G(s) 0 10,0 < b ≤ 10 U(s) s+b 1. What are the possible ways of connections? 2. When it will be used for each connection?
According to STAAD-Pro Vsi software, sketch the idealization of Concrete-Steel roof frame where (z Ibay@7.5m). Plot and generate modeling of the frame structure shown below, Roof steel plate cladding thickness 1.3cm, floor concrete slab thickness 22cm, steel member section (vertical double C5X6), (horizontal standard MC6X18-in x and z direction), (inclined double angle L25X2X1/4), reinforced concrete column (30cm), reinforced concrete beam section (30 x 50cm) Note: means member in z-direction Steel frame 2m Reinforced Concrete Frame 9m (0,0,0) 4m 4.5m 4m Im 4m 4m
A manufacturer of programmable calculators is attempting to determine a reasonable free-service period for a model it will introduce shortly. The manager of product testing has indicated that the calculators have an expected life of 60 months. Assume product life can be described by an exponential distribution. T / MTBF -T / MTBF T| MTBF -т / МТВF T| MTBF -т / МТВF 0.10 0.9048 2.60 0.0743 5.10 0.0061 0.20 0.8187 2.70 0.0672 5.20 0.0055 0.30 0.7408 2.80 0.0608 5.30 0.0050 0.40 0.6703 2.90 0.0550 5.40 0.0045 0.50 0.6065 3.00 0.0498 5.50 0.0041 0.60 0.5488 3.10 0.0450 5.60 0.0037 0.70 0.4966 3.20 0.0408 5.70 0.0033 0.80 0.4493 3.30 0.0369 5.80 0.0030 0.90 0.4066 3.40 0.0334 5.90 0.0027 1.00 0.3679 3.50 0.0302 6.00 0.0025 1.10 0.3329 3.60 0.0273 6.10 0.0022 1.20 0.3012 3.70 0.0247 6.20 0.0020 1.30 0.2725 3.80 0.0224 6.30 0.0018 1.40 0.2466 3.90 0.0202 6.40 0.0017 1.50 0.2231 4.00 0.0183 6.50 0.0015 1.60 0.2019 4.10 0.0166 6.60 0.0014 1.70 0.1827 4.20 0.0150 6.70 0.0012 1.80 0.1653 4.30…