A set of two tubes is connected in the manner shown in Figure P1–65. Under a compressive load of 20 000 lb, the load is transferred from the upper tube through the pin to the connector, then through the collar to the lower tube. Compute the shear stress in the pin and in the collar.

Q: a) Find expressions for normal force, shear force and bending moment diagrams as functions of x…

A: The given solution is an example of using mechanical design to solve a problem requiring a frame,…

Q: Given the configuration in Figure 1, calculate the load that can be supported under the following…

A: GIVEN; Pin diameter =10 mm =0.01 m Ultimate strength σut = 195 MPa FOS =2 Strength of cable = 207.5…

Q: Problem 4 only, solve carefully, include the units in every step and draw the diagram. Thanks! A…

A:

Q: A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in…

A: Coupling : It is a mechanical element which connect the shaft from another also it is used to…

Q: Problem 8-53: The coiled spring is subjected to a force P. If we assume the shear stress caused by…

A: Given Data:A coiled spring is subjected to a force P.The shear stress caused by this force on any…

Q: For condition I: It was given to you to use SAE1040 hot rolled steel project, you select a different…

A: Condition 1 : SAE 1080 is the first condition. Because the characteristics of annealed steel and…

Q: The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the…

A:

Q: 3 650.00 mm 60 kN 650.00 mm 50 kN 650.00 mm B 1,150.00 mm The pin at C has a diameter of 36 mm.…

A:

Q: 0o o o

A: GIVEN :- Load : P=70 kips F=35 kips l=15 feet Fultimate=58 kips Solution : Ultimate load is given by…

Q: 1. A collar is fitted as a tight fit on a solid shaft. In the measurement made before assembly, the…

A:

Q: The five-bolt connection must support an applied load of P= 196 kips. If the average shear stress in…

A:

Q: The tensile load on the bar mentioned varies from 4,000 lb to a minimum of 1,200 lb.  Rapid cycling…

A:

Q: For a specific spring where the load applied is 100 N, coil diameter is 4 mm, spring diameter is 20…

A:

Q: In the clevis shown in Figure 4.3, find the maximum bolt diameter and the minimum thickness of each…

A: Shearing stress is defined as the ratio of load to the shear area. When this shearing stress exceeds…

Q: 600 N Problem 5: Fatigue A bicycle crank experiences cyclic loading due to the force applied by the…

A:

Q: 4. A packaging machine mechanism has a link with a square cross section of 0.50 in on a side. It is…

A:

Q: A shaft with a diameter d = 25 mm must transfer a torque of 23 Nm by using a key joint. The key has…

A:

Q: A countershaft carrying two V-belt pulleys is shown in the figure. Pulley A receives power from a…

A:

Q: 3-81: Figure P3-81 shows two rods, AB and BC, supporting a load at B. Each rod is steel and has a…

A: Given Data,

Q: The tie-rods in the press in Figure are made of the steel alloy SAE 5160 OQT 900 (E-30×106 psi).…

A:

Q: Calculate the dimensions of the I-section of a connecting rod, stating any assumptions. using the…

A: The information provided in the image includes:Maximum cylinder pressure: 3.15 N/mm²Cylinder bore:…

Q: 12 mm Determine the following: a. Shearing Stress in the head bolt. b. Shearing in the thread c. The…

A:

Q: 3. The members of the structure in figure below weigh 280 lb/ft. Determine the smallest diameter pin…

A:

Q: 175 k 175 k The bolted to C d. connection shown is to be used to transmit a tension of 175 kips by…

A: .

Q: Condition #1: A structural support for a machine is subjected to a static compression load of 20 kN.…

A: Yield stress is the indication of the transition from elastic to plastic. It is the minimum stress…

Q: Suppose the load in the figure below is 2 kN. Further suppose that the distance between the load and…

A: Given : P= 2kN The distance between load and centroid is 1.3 m The horizontal distance between bolt…

Q: 2. Calculate the shear stress in a simple pin joint, assuming pin diameter of 10 mm and 3550N…

A:

Q: In the clevis shown in Fig. 1-11b, the minimum bolt diameter (d=22mm) and the minimum thickness of…

A: Given data  Diameter = 22 mm Thickness = 10 mm Shear stress = 83 MPa Bearing stress = 138MPa Find…

Q: The metal stud punch shown in the figure below is designed to create circular shaped perforations on…

A:

Q: The squared and grounded ends of a safety valve with 7.5 coils. The coils measure 105 mm in diameter…

A:

Q: Problem 3: Compute the factors of safety for the configuration. Bar and pin dimensions, limiting…

A:

Q: The pin in the image shown below must transfer an axial tension force of 12.7 kN. Calculate the…

A:

Q: cross section, side length b, and wall thickness t. The second is a round of diameter b and wa…

A:

Q: A pushrod in the valve mechanism of an automotive engine has a nominal length of 203 mm. If the rod…

A:

Q: Try One - scene 8 of 8 Pin diameter = 24 mm For the pin connection shown, determine the normal…

A: Write the formula for the normal stress acting on the gross area. σgross=PAgross Here, P is the…

Q: Problem 1: The assembly below will be used for each problem. Lengths, diameters, and materials are…

A:

Q: 1. Two plates are connected by bolts as shown in the figure. Compute the bearing stress in each…

A:

Bending Moment

In general, we can define the bending moment as the reaction induced when a certain amount of load or force is applied to an element which makes it bend.