A series R-L-C circuit has the following voltages across its elements: V₁ = 43.3 V, V₁ = 40 V and Vc = 15 V. Find the supply voltage. Select the correct response: 70.7 V 35.4 V 50 V 92 11

Q: a) A sinewave is having a frequency of 100 Hz and instantaneous value of 250 Volts at 1.2 milli…

A:

Q: QUESTION 22 The total current in this circuit is 30 V 23 kHz L1 2.1 mH R1 400 O 24mA 75mA 124mA O…

A: The solution is given below

Q: Geometric Mean Radius (GMR)

A:

Q: 22. For the circuit of Figure 2.33, determine the circulating current and the voltages across each…

A: The solution is given below

Q: +30°C. What is (a) the range, (b) temperature control system has a set point of 20°C and the…

A:

Q: A continuous-time signal is given by x(t) = 10e-5tu(t). 1. Determine the frequency response X(jw)…

A: 1)The question is about Fourier transform.By terms and conditions I am doing only first question.

Q: 2. Show that a rfo/Q for a parallel RLC resonance cir 4 R ww CA

A:

Q: A circuit with 6 2 resistance and 8 2 inductive reactance is connected across a 200 V 50 Hz mains.…

A:

Q: 14. Determine the valuc of load voltage (Vµ) for the circuit shown in Figure 6.46b.

A:

Q: Draw a signal flow graph for the following set of algebraic equations: Y2 = ay₁ - 9Y3 Y3 = ey₂ + CY4…

A: We have to draw the signal flow diagram for the following algebric equations: y2 = ay1 - gy3 y3 =…

Q: For the circuit shown below, Write mesh1, mesh2 and mesh3 equations Calculate the voltages vR1, vR2,…

A: For this circuit we need to calculate the mesh equation and voltages V R1,VR2,VR3,VR4.Circuit:-

Q: (a) s²+2s +1' (b) 22. The input x and output y of a system are described by: $²+7s + 12' dy dx + 2y…

A:

Q: A- A 10 kHz signal wanted to be sent and encrypted using FHSS with a factor of 10, if Af-5KHz…

A: FHSS stands for Frequency Hopping spread spectrum. It is a wireless communication technique where…

Q: For the circuit below, the sources are given in RMS. 592 40/90° V ww +1] 8Ω Ξj2Ω ww 11 12 3/0° A 10…

A:

Q: Q2) A generator is connected to a constant voltage bus through an external reactance of 0.3 per unit…

A: In this question we need to find the critical angle and critical time for the given system

Q: A: A single core cable covered by the lead, if the radius of the cadactor is r and the insulator…

A: Cross Section of Underground Cable: Given:Single Core Cable covered by Lead Radius of conductor =…

Q: 4. For the circuit in the figure shown calculate the voltage Vx.

A: It is given that:

Q: A DC voltage source has a source resistance variable from 5 0 to 25 Q and it is connected to a load…

A: Given, A DC voltage source has, Source resistance, Rs=5 Ω to 25 Ω variable Load resistance, RL=10 Ω.

Q: MAIN QUESTIONS 1. Figure 1 shows a full adder combinational logic circuit which is used to add three…

A:

Q: QUESTION 23 In a low pass RL filter circuit, the inductor is placed O in parallel with the output…

A:

Q: An inductive load is controlled by an impulse commutation chopper in Fig.1 and peak load current…

A: “Since you have posted question with multiple sub parts,we will provide the solution only to the…

Q: When an RLC circuit is driven at its resonant frequency, which of the following statements is true?

A: given RLC CIRCUIT

Q: You are given the circuit shown below. Note that the connected to the + terminal of the capacitor…

A: Since you have asked multiple questions in a single request, we will be answering only the first…

Q: admittance Hybird paramter(h).

A: The solution can be achieved as follows.

Q: Refer to the circuit below, Which of the following is true about the voltage across R₁? RGI Ra 800…

A: Apply kvl in the circuit.

Q: QUESTION 14 If phasors A and B represent sine waves A and B, what is the phase angle of the two…

A: we have the two waves  A and B in which A is originating from the 0 and B is originating 180 degrees…

Q: Q.NO.2. For the emitter bias network of Fig. 2, a) Calculate the output voltage if Rs = 1000 and RL…

A: For the emitter network of fig 2, b) Determine what will happen to the output voltage if RL becomes…

Q: 1. Consider the following Laplace Transform s+2 X(s) s2 + 7s + 12 (a) List all possible ROCS. (b)…

A: Given transfer function: (a) To determine the possible ROCs The transfer function can be written…

Q: voltage? 23. Determine the compensating resistor value for each amplifier configuration in Figure…

A: It is given that:

Q: Ven b n a) Von Rw www an 2+1 Rw www FIGURE 12.34 B p 41 R www Zp A 18 Exercise 17 with R₁ = 10 92,…

A: Each impedance Z, in the balanced three-phase system of above diagram is constructed using the…

Q: find the current through 15 22 resistor 20 Ω ww 40 V 0.90A 0.84A 0.51A 0.48A www 5Ω…

A:

Q: Suppose 81 (t) has energy E₁ = 4, 82 (t) has energy E₂ = 6, and the correlation between $₁ (t) and…

A: Given Data:1.Energy of signal is Energy of signal is Correlation of signals Number of signals used…

Q: 4. What is the magnitude of the static electric force at point C? • Q.= 3.2 µC; r = (6m, 8m) Qa=…

A: It is given that: QA=3.2μC; r=6m,8mQB=-7.8μC;r=0,8mQC=9μC;r=0,0

Q: QUESTION 18 What is the approximate amplitude of this waveform when one division represents 2 volts?…

A: In this question,   We need to choose the correct options What is amplitude of this waveform?

Q: A large 3-phase, 4000 V, 60 Hz, squirrel- induction motor draws a current of 23 cage 385 A and a…

A:

KVL and KCL

KVL stands for Kirchhoff voltage law. KVL states that the total voltage drops around the loop in any closed electric circuit is equal to the sum of total voltage drop in the same closed loop.

Sign Convention

Science and technology incorporate some ideas and techniques of their own to understand a system skilfully and easily. These techniques are called conventions. For example: Sign conventions of mirrors are used to understand the phenomenon of reflection and refraction in an easier way.