Answered: A series circuit of resistance 60 2 and…

A series circuit of resistance 60 2 and inductance 75 mH is connected to a 110 V, 60 Hz supply. Calculate the power dissipated.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 1PA: Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter...

See similar textbooks

Related questions

Q: 4. a. For the waveform shown in figure5, determine (i) Peak value (ii) (iii) (iv) the peak-to-peak…

Q: Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and…

A: A limiter circuit should be designed that limits a 20 V rms sinusoidal voltage to a maximum positive…

Q: a p.d. of 500 V is applied across the winding of an electric motor and the resistance of the winding…

A: Given the winding of an electric motor having, Potential difference across the winding, V = 500 V…

Q: A series circuit consisting of 10 ohm resistance and 60 mH inductance is connected across a 220…

Q: 1. Find the average value of current when the curren that are equidistant are 4A, 5A and 6A.

A: It is given that:

Q: ohm resistor in series with a 7.96 milliHenry inductor is connected across a 110-V 60-Hz and (c)…

Q: 10. Determine the peak-to-peak ripple and de output voltages in Figure 5. The transformer has a 36 V…

A: Given circuit parameters: Supply voltage - 120 Vrms Wheat-stone full-wave rectifier Rsurge = 10 ohm…

Q: direct current of 12.5 A flows in a 25-ohm resistance. Determine the maximum value of an alternating…

Q: Oscilloscope measurements indicate that the peak voltage across a load and the peak current through…

A: In this question, We need to determine the power factor. We know Power factor = cos(θ) = cos(V^I)…

Q: A 20 V peak sinusoidal voltage is applied to the circuit in Figure 2 in place of the dc source. Draw…

A: The given circuit digram is shown below, IZ=40 mA.VZ=12V at 30 mA.ZZ=30Ω.

Q: A direct current (DC) of 4A flows into a previously uncharged 20 µF capacitor for 3 ms. Determine…

A: Given: Direct current, I=4 A Uncharged capacitor of capacitance, C=20 μF Time, t=3 ms

Q: Find the Current in the Circuit in Miliampares

Question

A series circuit of resistance 60 2 and
inductance 75 mH is connected to a 110 V, 60 Hz
supply. Calculate the power dissipated.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
A series circuit consists of a 66.4 microfarad capacitor and variable resistor. For what two values of resistance will the power taken by the circuit be 172. 8 W, if the impressed 60 Hz emf is 120 V?
2. A resistor in series with a capacitor absorbs 10 W when the combination is connected to a 120 – V, 400 – Hz source. If the power factor is 0.6 leading, what are the resistance and capacitance?
If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship between the applied circuit voltage and the circuit current? The applied voltage lags the circuit current. The phase shift between the circuit voltage and current changes with time. The applied voltage is in phase with the circuit current. The applied voltage leads the circuit cur Previous Page Next Page Page 2 of 10
The initial rate of current rise in an RL circuit is 300 amp per sec when 120 volts is suddenly impressed. What is the inductance of the circuit?
Please help me answer. Thank you.
A 750-ohm resistor, an uncharged 1.50 uF capacitor, and a 8.00-V emf are connected in series. (a) What is the current after one time constant? (b) What is the voltage on the capacitor after one time constant?
AC Circuits Sine-wave generator f- 25 kHz V₁ = 3.0 V VR 888 100 mH Figure 6-Test Circuit 3. Using a two-channel oscilloscope, measure the peak-to-peak voltage VR across the resistor and the peak-to-peak voltage VL across the inductor. Measure the voltage across the inductor using the difference technique described in a previous experiment. Record the voltage readings in Table 2. VL 10 k 1 XL Table 2- Measured and Calculated Values (f = 25 kHz) ZT
Write solution neatly
A 1-H inductor is connected in series with a 6-ohm resistor. If the connection is energized from a 9-V DC source, determine the current (in amperes) through the circuit for a long time. The initial current is 100 mA. Express your answers accurate to four decimal places. No need to put the units.
In general, the greater the absolute value of the impedance in a circuit:A. The greater the flow of alternating current.B. The less the flow of alternating current.C. The larger the reactance.D. The larger the resistance.
ANSWER ASAP PLS