A series circuit contains a resistor and an inductor. as shown in figure 1.31. determine a differential equation for the current i(t) if the resistance is R, the inductance is L, and the supplied voltage is E(t).

Q: istance is R, the inductance is L, and the impressed voltage is E(t). (Use i for

A:

Q: A parallel-plate capacitor having square plates 4.50 cm on each side and 8.00 mm apart is placed in…

A:

Q: Describe the cutoff condition in a BJT circuit?

A: The cutoff mode is the opposite of saturation. A transistor in cutoff mode is off, there is no…

Q: For problem 33.5 calculate the inductance in zeptohenries if the capacitor has a value of 22…

A:

Q: A 4900-pF capacitor is charged to 120 V and then quickly connected to an inductor with 83-mH…

A:

Q: For a driven series RLC circuit, the voltage amplitude Vo and frequency f of the voltage generator…

A:

Q: A series circuit has a capacitor of 0.1 · 10-6 F and an inductor of 2.5 H. If the initial charge on…

A: The capacitance if the capacitor is given as, C=0.1×10-6 F The inductance of the inductor is given…

Q: (a) For the RL circuit, the equation was: dI E – L dt IR=0 Show by direct substitution that I(t) =…

A: For RL circuit the equation is, ε-LdIdt-IR=0 Substituting I(t)=εR1-e-RLt in left hand side,…

Q: Suppose a 32 mH inductor has a reactance of 95 Ω. What would the frequency be in Hz?

A: KnownsUnknowns

Q: An LRC circuit is set up with an inductance of 1/5 henry, a resistance of 1 ohm, and a capacitance…

A:

Q: 0- 0.5- 0.0- XE Auto Fit for: Latest | Potential Pot A (1-exp(-C'(t-10)))+B to: 6.72988 A: 1.283…

A: if we consider Y=B as our origin then the equation of fit line will become  A(1-e-C(t-to))…

Q: In a series RL circuit like (Figure 1), ε0 = 40 V, R = 3.0 Ω, and L = 2.4 H. If the current is 8.7…

A:

Q: where f is the frequency and L is the inductance. If the inductive reactance is 345 V and the…

A:

Q: Find the equation of the current i(t) as a function of time in a series Resistor-Inductor (RL)…

A: equation is iR+Ldidt=V10i+didt=10e-5t

Q: Problem 9.5 Use the value of the inductance and capacitance of a pair of plane parallel conductors…

A: Given, Characteristic impedance of waveguide.

Q: 3. Find the value of the inductive reactance when A.C. voltage of 220 V at 50 Hz is passed through…

A: Given data: AC voltage (V) = 220 V Frequency (f) = 50 Hz Inductance (L) = 10 H Required: The value…

Q: An RL circuit is assembled with a 24.0 V ideal battery connected by a switch to a 37.5 mH inductor…

A:

Q: In the circuit shown in the figure below, a battery supplies a constant voltage of 36 V, the…

A:

Q: Ex.4 A 3500-pF capacitor is connected in series to a 55 uH coil of resistance R=4 Ohm What is the…

A: Write the given values with the suitable variables. C=3500 pF=3500×10-12 FL=55 μH=55×10-6 HR=4 Ω…

Q: In the system shown below, the generator is ideal (Xs 0) and the magnitude of the load bus voltage,…

A: a) The presence of transformers causes the base voltage to vary as we move back from the load…

Voltage Across Inductor

An actor is a passive electrical component that consists of a coil bent in the form of wire which uses electromagnetism to produce electric current through the coil. When the electric current flows through a conductor that is the coil, a magnetic flux is developed around the conductor. This flow of current through the coil creates a magnetic field based on Fleming's Right-hand thumb rule. If there is any decrease in the current passing through the inductor, then the magnetic field will also decrease and energy is released through the generation of electric current. There is also a secondary voltage inducing in the same coil due to the magnetic flux, since it opposes any changes in the electric current flowing through the circuit. An inductor is also called choke, coil, or solenoid. A choke is designed to block certain frequencies when the DC current passes. A winding coil is coated with insulation to give extra insulation and protect the circuit. They are usually tightly wrapped around a central core which is cylindrical in nature so that the magnetic flux can be induced. The solenoid is a three-dimension coil that is used to exhibit electromagnetism when the magnetic field is developed due to the current flowing through the coil. The sign convention of the inductor is the same as the power dissipating device. When the current flows into the positive side of the voltage across the inductor, the value is positive and the inductor dissipates power whereas when the inductor releases the power back to the circuit, the current has a negative sign convention.