A Semiconductor diode is used inhalf-waveresistive Load ofrectifier Circuit Supplying1000_2. If the Vrimis Value of the SinusoidalSupply Voltage is 250V, determine3 I 9(9) The Peak load CurrentLoadCurrent(b) The(9) TheMeanr.m.sThe Powerload Currentdissipated in the load.

Answered: Image /qna-images/answer/1974c847-b048-4087-be15-ee524a361120.jpg

A Semiconductor diode is used in rectifier Circuit Supplying 1000_2. If the Vrimis Value of tho Sinusoidal Supply voltage is 250V, determine (9) The Peak load Current (b) The Load Current Mean half-wave resistive Load of The r.m.s d The Power load Current dissipated in the load.

A Semiconductor diode is used in rectifier Circuit Supplying 1000_2. If the Vrimis Value of tho Sinusoidal Supply voltage is 250V, determine (9) The Peak load Current (b) The Load Current Mean half-wave resistive Load of The r.m.s d The Power load Current dissipated in the load.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the half-wave rectifier shown below. It needs to deliver 0.1 A and an average of 15 V to a load. The source is 60 Hz and the diode has a 0.7 V drop. The allowable ripple is no more than 0.4 V (2.5%). Find: Peak AC voltage Vm of the source a) b) The minimum value of the smoothing capacitor(s) c) Comment on the type of capacitor and its/their values you would use for this amount of capacitance vs(t) K Load UL
: Find the average and rms values of the sinusoidal voltage measured at the output of full-wave rectifier.
Draw the following rectifier circuits with an input voltage of 12 Vrms and an RL=2K. Determine the output voltage and the current in RL. Plot these waveforms indicating the peak values and the time as per calculation. Also solve for the output DC value. Use silicon diode/s in your analysis. Half wave rectifier circuit (include the diode voltage analysis), Full wave bridge rectifier circuit, Full wave rectifier using center tapped transformer
Draw the circuit diagram of a single phase full-wave uncontrolled rectifier with R-load. Describe its principle of operation. Draw the waveforms of: input voltage, voltage across the load, current through the diodes and their voltage. Write the expressions for: the average output voltage Vd, the maximum reverse voltage across the diode and the standard transformer power. Describe what the difference will be if a capacitor is added in parallel with the load at the output. 1.
3A Semiconductor half wave resistive load of rectifier circot Supplying 1000 a. If the r.m.s Value of the Sinosidal Supply Voltage is 250V. Draw the Circuit and determine i Average Voltage Voltage I.d.c diode is way in a across Load
Design a Zener diode voltage regulator with a suitable circuit diagram and to consider the voltage regulator is used to power a cell phone at 4.5 V from a lithium ion battery pack, which voltage may vary between 5 V and 7.8 V. The current in the phone will vary 10 mA (when standby mode) to 150 mA (when talking). Assume that the Zener diode current, Iz(min) is 10% of Iz(max).
A Half-Wave rectifier with a capacitor filter (capacitance is 4700 ?? ) supplies to a load an average current of 1.4 A at an average voltage of 19.5 V. Determine: a) the ripple factor, b) ????.
a) Find the value of DC voltage of the RL load resistance.b) Find the required rated PIV values for each diodes.c) Find the maximum conduction current of the diodes.d) Plot waveforms of the output current and voltage values.
. A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA. The peak-to-peak ripple is required to be 0.2 V or less. What is the minimum value allowed for the smoothing capacitance?
Refer to the circuit. Consider ideal model (V_D=0) of diode circuits. Given V_i =100 Volts peak-to-peak sinusoidal input (+50, -50 Voltage peaks). Determine the peak output voltage during the diode non-conduction cycle.
Consider the full-wave rectifier circuit shown below, where• vS(t) is a sinusoidal signal with a peak value (Vs = 5 V).• Diodes are modelled using constant voltage model with VDO = 0.7 V• The ac line voltage has an rms value of 120 V and a frequency (f) = 60 Hza) Calculate the transformer turns ratio. b) Plot in the same graph signal vS(t) and the output signal vO(t) versus time (t) (show all details including amplitudes, time instances, etc.) c) Calculate the rms value of the output signal vO(t). (hint: sin2(x) = 0.5(1- cos(2x))) d) If a capacitor C=3.58 F is connected across R = 10 k, repeat (b) in a new graph
For the full wave rectifier circuit shown, if vs=15sin(120nt) (V), R=10052, assuming constant voltage drop with VDo=0.7 J. 1. LDraw clearly and accurately with details the following waveforms: Source voltage (vs), load voltage (v.) 2. Describe in details the operation of the circuit indicating which diodes will be ON which ones will be OFF and state clearly the condition at which each diode will be ON or be OFF. 3. Calculate the mean load current (IRmean) given Vmean=2Vp/T. 4. Calculate the PIV. ac line Us voltage D2 Maximum size for new files: 10MB, maximum attachments: 2 Files 79 CE255/EE255 (01)-..