, A second order band-pass filter is designed by cascading filters in Fig.(1-a) and Fig-(1-b) its required to: a- Draw a resultant circuit BPF. b- Derive H(s) for BPF in a. c- Determine upper and lower cutoff frequency then calculate a center frequency and a band width for BPF. d- If the gain is 2.121 at the upper cutoff frequency determine the quality factor, the gain at the center frequency then draw the frequency response.

, A second order band-pass filter is designed by cascading filters in Fig.(1-a) and Fig-(1-b) its required to: a- Draw a resultant circuit BPF. b- Derive H(s) for BPF in a. c- Determine upper and lower cutoff frequency then calculate a center frequency and a band width for BPF. d- If the gain is 2.121 at the upper cutoff frequency determine the quality factor, the gain at the center frequency then draw the frequency response.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design an active high pass filter with a specified Passband break frequency of 1.100 rad/sec and a gam equal to 22. use a capacitor Vahe of loont, For these design, Show: ⑥A circuit diagram of final filter design, Label all Components and Indicate the luput and Output Locations. Do not luctude De Power to the op-amp. ⑥The Jw transfer Function For The Filters -D The Passband gan in dB use the tf and bode command In MATLAB a bode Plot for the filter that the Passband to generate Confirming and the break frequency CLabel both 2nd gan Correat A
Design 1. Use Matlab DSP functions for the design and practical implementation of the BP filter in its FIR version with 64 taps. Specify the values for the cutoff frequency fp and the stop frequency fs of the BP filter, in terms of the Nyquist frequency, with the following characteristicsA bandpass (BP) filter, with cutoff frequencies of 500 Hz and 1 kHz, is required to process the stream of an audio signal sampled at 8 ksps. please share me the code in .m
Referring to the figure below, with Rs = 0.82 kohms Determine fLS , fLC, and fLE . [Re= RE||(R's/beta + re)], R's=Rs||R1||R2 Determine fHi and fHo note: all of the formulas are given. please show complete solution.
For the low-pass active filter shown below, the transfer function is expressed as: V. V ZR + Zc Zc where: 106 = 2000 , Zc jw rad w = angular frequency in [ ZR ZR Vi o V. 4-A) Show that the e can be written as: V. 500 V 500 + jw 4-B) What should be the value of w so that the magnitude of V10 ? 4-C) With w = 1250 rad/s, and Vị = 9el1.8 – j10 volts, evaluate the magnitude and phase of V. Vo (Hint: evaluate in polar form, and Vị in polar form, then V, = x Vị ) 4 4-D) When 4 modules of this filter are cascaded, the total transfer function will be (. Use de Moivre's Theorem to find the expression of the total transfer function in polar form. Then, find determine the value of w so that the magnitude of the total transfer function is V10 ?
HW2) A second order band-pass filter is designed by cascading filters in Fig.(1-a) and Fig.(1-b) its required to: a- Draw a resultant circuit BPF. b- Derive H(s) for BPF in a. c- Determine upper and lower cutoff frequency then calculate a center frequency and a band width for BPF. d- If the gain is 2.121 at the upper cutoff frequency determine the quality factor, the gain at the center frequency then draw the frequency response. R1 723.42 C2=0.01µF R2 Vi C1=0.01µF- Vi 8849 V. V, a Fig.(1) ww
Analogue Electronics II Design 2 different configurations of active band pass filter for the frequency with bandwidthof 200 Hz.Design A has the quality factor Q less than 10, is independent on the critical frequency,whereas Design B has the quality factor, Q more than 30, is dependent on the criticalfrequency. You can use your own value of resistors and capacitors in the design. Show allrelated calculations (eg. fc, fo, Q, Gain, Bandwidth) and the final circuit design.
DESIGNPROBLEM_PSPICEMULTISIM Use a 500 nF capacitor to design a bandreject filter, as shown. The filter has a center frequency of 4 kHz and a quality factor of 5. 1. a) Specify the numerical values of R and L. 2. b) Calculate the upper and lower corner, or cutoff, frequencies in kilohertz. 3. c) Calculate the filter bandwidth in kilohertz. Vi 500 nF HE L R Vo
We are going to sample several signals with different maximum frequencies at 10rad/s. Let's assume that the sampling frequency is fast enough for us to reconstruct the original signal. What filter should we use to reconstruct the original signals? O A LPF with a magnitude of 1 at –10 < w < 10 and zero otherwise O None of the above answers O A LPF with a magnitude of at –5
Please do part D
H.W2: a) Using 0.1 uF capacitors, design an active broadband first-order bandpass filter that has a lower cutoff frequency of 200 Hz, an upper cutoff frequency of 2000 Hz, and a passband gain of 0 dB. b) Write the transfer function for the scaled filter. c) Use the transfer function derived in part (b) to find H(jwo)where wo is the center frequency of the filter. d) What is the passband gain (in decibels) of the filter at wg?