11:05!!:Classroom >docs.google.com aquestionA screw jack as shown in Fig.3 has the following data: Outer and iner diameterof the screw is 20 mm and 15 mm. pitch 5 mm, square threads, coefficient offriction, u. is 0.15 and its lead, I, is 10 mm. Find the torque required, T, for risingthe car if the capacity of the screw jack, F (10,12,1.1,16,18,20,2'2) kN. Thefollowing formula can be applied,1+2undm sec andm - ul sec aT = Fwhered, mean diameter= (inner diameter +outer diameter)/2a: angle and equal to zeroFig.3.1 Add fileRead and answer *Create a row vector that has the following elements: 8. 10/4, 12x1.4, 51.tan 85°,V26, and 0.15.Use a single command to create a row vector (assign it to a variable named b)with 11 elements, such thatb = 0 2468 10 12 9630Do not type the vector explicitly.1 Add file+->13

There can be two approaches to this question either we take mean of range of forces acting on the…

A screw jack as shown in Fig.3 has the following data: Outer and inner diameter of the screw is 20 mm and 15 mm, pitch 5 mm, square threads, coefficient of friction, u. is 0.15 and its lead. 1, is 10 mm. Find the torque required. T, for rising the car if the capacity of the screw jack, F = (10,12,1.1,16,18,20,2'2) kN. The following formula can be applied, 1+ 2µnd sec a T= F adm - pi sec a where d, mean diameter= (inner diameter +outer diameter)/2 a: angle and equal to zero Fig.3.

A screw jack as shown in Fig.3 has the following data: Outer and inner diameter of the screw is 20 mm and 15 mm, pitch 5 mm, square threads, coefficient of friction, u. is 0.15 and its lead. 1, is 10 mm. Find the torque required. T, for rising the car if the capacity of the screw jack, F = (10,12,1.1,16,18,20,2'2) kN. The following formula can be applied, 1+ 2µnd sec a T= F adm - pi sec a where d, mean diameter= (inner diameter +outer diameter)/2 a: angle and equal to zero Fig.3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Toe Hinge-Pins Hel The brake shown in Fig. 1 is R=170 mm inner radius of the drum and is actuated by two hydraulic pistons that exerts the same force F =2800N, on each shoe. The shoes are identical and have the same unknown face width. The lining material has a coefficient of friction u=0.3 and a maximum pressure of P3=1050 kPa. The other dimensions are e = 130°, a = 21° B = 29°, p = 150 mm, d = 47 mm %3D Determine the (a) The face width in millimeters. (b) Pressure in the left-hand shoe in (kPa). (c) The braking torque in (Nm).
Solve the following problem (NOTE: Use any reasonable DATA not given in the problem.)
The coefficient of friction between the belt and the pulley is 0.3 and the maximum stress in the belt is limited to 14 N/mm width. If the larger pulley rotates at 120 r.p.m., find the maximum power that can be transmitted. Q2 Find the diameter of a shaft made of 37 Mn 2 steel having the ultimate tensile strength as 600 MPa and yield stress as 440 MPa. The shaft is subjected to completely reversed axial load of 200 kN. Neglect stress concentration factor and assume surface finish factor as 0.8. The factor of safety may be takenas 1.5. Q3 a) An universal coupling is used to connect two mild steel shafts transmitting a torque of 6000 N- m. Assuming that the shafts are subjected to torsion only, find the diameter of the shaft and the pin. The allowableshear stresses for the shaft and pin may be taken as 55 MPa and 30 MPa respectively.
2. The clamp of the given figure is used to hold a cover in place. The screw of the clamp has a single thread with a mean radius of 0.20 in and a pitch of 0.08 in. The coefficient of friction is 0.45, and the required clamping force is 100 lb. (a) Determine the twisting moment to tighten the clamp and (b) determine the twisting moment to loosen the clamp.
Please help. Written on paper not typed on computer please. Need help on all questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
(b)Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also gIven pitch = 8mm and coefficient of friction is 0.15?
Question 2 A aluminium wheel of diameter 200 mm carries a load of 800 N.If 200 N force required at center to roll the wheel. calculate the coefficient of rolling friction.
A single-threaded 25-mm power screw is 25 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN. The coefficients of friction are 0.06 for the collar and 0.09 for the threads. The frictional diameter of the collar is 45 mm. Find the overall efficiency, and the torque to “raise” and “lower” the load. If the effort load is 75 N, find the force ratio and movement ratio.
QI: A double-threaded 30-mm power screw is 30 mm in diameter with a pitch of 6 mm. The coefficients of friction are 0.05 for the collar and 0.08 for the threads. The frictional diameter of the collar is 40 mm. if Tg=18 N.m: 1- Find the A vertical load on the screw, the torque used to lower the load and screw efficiency. 2- Compute all the stresses on the screw body that will cause by the load.