A SCR has gate characteristics given by Vg = 91g +10The gate signal is a triggering pulse of amplitude 30V and duly ratio of 0.4. average gate powerdissipated 0.6 W. in the figure below ,that thyristor connected to de supply100V feeds a load havingan inductance of 2.5H and a resistance of 5N.Hints: where 0.35 and 0.25 current gain of NPN and PNP respectively of two transistor models,while all leakage currents are neglected.Find in details:1-value of :series resistor Rg connected with the gatecircuit, Ig, and Vgtriggeringcircuit100 V2- anode current.RL-3- triggering frequency of the gate pulsesload

" Since you have asked multiple questions, we will solve the first question for you. If you want an…

A SCR has gate characteristics given by Vg = 91, +10 The gate signal is a triggering pulse of amplitude 30V and duly ratio of 0.4. average gate power dissipated 0.6 W. in the figure below ,that thyristor connected to de supply100V feeds a load having an inductance of 2.5H and a resistance of 52. Hints: where 0.35 and 0.25 current gain of NPN and PNP respectively of two transistor models, while all leakage currents are neglected. Find in details: 1-value of :series resistor Rg connected with the gate circuit, Ig, and Vg triggering circuit 100 V 2- anode current. RL- 3- triggering frequency of the gate pulses load

A SCR has gate characteristics given by Vg = 91, +10 The gate signal is a triggering pulse of amplitude 30V and duly ratio of 0.4. average gate power dissipated 0.6 W. in the figure below ,that thyristor connected to de supply100V feeds a load having an inductance of 2.5H and a resistance of 52. Hints: where 0.35 and 0.25 current gain of NPN and PNP respectively of two transistor models, while all leakage currents are neglected. Find in details: 1-value of :series resistor Rg connected with the gate circuit, Ig, and Vg triggering circuit 100 V 2- anode current. RL- 3- triggering frequency of the gate pulses load

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

You are tasked to design a dc power supply that operates from a single-phase ac supply (50Hz) with source inductanceof 1.5mH/phase. It is required to supply a dc load (resistive) with 55A at 322 Volt. Assume infinite inductive filtering andthe use of power diodes with a forward voltdrop of 0.7V. Consider the bridge converter topology and specify the followingdesign parameters,30) the loss in voltage due to commutation overlap;31) the r.m.s. ac supply voltage required;32) the overlap angle;33) the transformer utilisation factor;34) the rectification efficiency of the converter;35) the dc current rating of the rectifier diodes;36) the r.m.s. current rating of the rectifier diodes;37) the form factor of the diode current;38) the peak repetitive forward current rating of the rectifier diodes;39) the peak repetitive reverse voltage rating of the rectifier diodes
In a full-bridge dc-dc converter using PWM bipolar voltage switching, analytically obtain the value of (V/V) which results in the maximum (peak-peak) ripple in the output current i,. Calculate this ripple in terms of Va, La, and f
QUESTION 4 For an n-channel Junction Field-Effect Transistor (JFET), the gate-source cut-off voltage, VGS(OFF), is -4 V and the drain saturation current, Ipss is 50 mA. The drain current ID, is 12 mA. Determine the gate-to-source voltage, Vos, of the JFET.
Assume R1= R2 =D6002, RL=500, and Vcc = 15V. Assuming D1 and D2 are identical and have same characteristics as Q1 and Q2 base-emitter junctions, if the input voltage is 1Vrms, what will be the output peak voltage? Vcc R1 D1 D2 Q2 R2 R2 -Vcc
Question 1.1 (correcta) In the case of the circuit shown, it is a resistance that increases in value with increasing temperature. This type of thermistors are of the PTC (Positive Temperature Coefficient) type. Transistor Q1 is an N-channel enrichment MOSFET model HB-NR066, which has a threshold voltage VT= 3V, and turn-on values ID (on)= 10 mA and VGS(on)= 7V. The circuit It is used as a temperature-to-voltage converter for an industrial process, since the output voltage Vo changes with temperature. From the above, develop the following points.a) If it is known that at a temperature 50 degrees Celsius the value of the thermistor is RT= 5k Ω find the operating point of the transistor for this temperature, as well as the output Vo. Also, perform the necessary calculations to verify that Q1 is in the saturation zone.
Problem-5 The LED in Figure below requires 30 mA to emit a sufficient level of light. Therefore, the collector current +Vcc should be approximately 30 mA. For the following circuit values, determine the Re amplitude of the square wave input voltage necessary to make sure that the transistor saturates. Use double the minimum value of base current as a safety ON ON margin to ensure saturation. OFF Vcc = 9 V, VCE(sat) = 0.3 V, Rc = 220 N, RB = 3.3 kÝ Bpc =50, and VleD = 1.6 V. 1
1- a. For the circuits given below calculate the currents through the zener diode (V5.1V) and the current through the Si-diode. 1k Ohm 1k Ohm -10V 1k Ohm 12V b. The emitter of an NPN type BJT is connected to ground. Its base is connected to a 5V supply with a 10K resistor. Its collector is connected to the same supply with a 6K resistor. Calculate the range of ß such that the transistor is not saturated.
a ): The depletion region is a layer of positive and negative charge in the semiconductormaterial Briefly explain how the depletion region formed in the semiconductormaterial after the PN junction is created.b): An audio signal amplifier is used to reproduce input audio signals at sound-producoutput elements, with desired volume and power levels. What is the function of volumecontrol and power amplifier in an audio signal amplifier ?
9
In saturation, both pn junctions are forward – biased and the collector current is in maximum.true or false
a) What is a Field effect transistor? Give its description and classification.b) Explain the working of n-channel / p-channel Junction Field EffectTransistor with its drain characteristics.
{1OB/s 4.ll Asiacell Untitled docu... -> Q/ Derive mathematical expression to determine the stability factors of voltage-divider bias circuit?